ID smd 6pin chip - GM2 for electric scooter display

[Ihandyrepair]

Hi

working on a not turning on Wheelspeed WS1 scooter.
diagnosed - issue is the display/power button

on the board, with the multimeter I noticed there is a short to ground. as the red wire has 0 ohm to ground.
with infrared camera, this chip (photo circled) would heat up if I push power button on.
but I can't find any replacement or online info of this chip.
on the chip you can see it has a label GM2H, I have another good working display with the same chip but it has label GM2C

could anyone help me id this chip and guide me to...

[ReparaPC]

I have an RTX 2070 Super from evga with a blown up IC. With the IC on the card, pin 17 had a short to ground. This pin is connected to the 5V rail by R993, a 0hm resistor. I removed both U610 and R993, to discover that the 5V rail has 800 Ohms of resistance to ground. After checking some resources online, i found a picture which describes the usual measurements a Turing series GPU should have in order to "work properlly". Interestingly enough, this gpu doesn't have U31, the IC responsible for the creation of the 5V on the card, as well as no L47.

Are these 800 ohms rigth...

[tommy97]

Hi, I've got bulk of lenovo l480 (joblot), all of them comes with bios password I'm looking for a good and reliable solution as we have loads of them, I do have SVOD 4 with keyboard connector, I haven't dealt with KBC PW yet and in my knowledge that's the case.

[learnmore]

Hi Community,

I've got the above model that activates the relay (clicks) and powers on the LG logo power light on when turned on. It then almost immediately turns off. I not noticed any image on the screen or heard any sound during this brief period.

Checks show:
3.5v on SMPS on (in off state, no other voltages present incl pwr on)
On pressing power button > the 3.5 pwn on voltage, 12v and 24v lines appear on the SMPS connnector between the main the SMPS but then all drop the zero in 1-2 seconds
Disconnecting 24 to TCON connector and powering on shows...

[steveoski]

Hey guys looking for the Bios for an Asus ROG G713PV-DS94
Motherboard Number is g713p-mb-VGT 6050A3468901-MB-A01
Serial Number is R3NRKD03613412E

i am not sure if any additonal information is needed if so let me know and i can update this post. Things i have tried are to download the BIOS directly from Asus but that file is a .329 file and is 32MB as opposed to the 16MB file i need. Scoured high and low and cant find this darn BIOS anywhere! Much appreciated!!...

[ResoluteHawk]

I have an Asus G14 (GA401QM) that has a power issue. Originally the board had a shorted 5V rail and dead EC. I reballed a working EC, soldered it on, and I resolved the 5V issue by replacing the APL6012 and the low side 5V mosfet. Resistances on all power rails are healthy now, but 20V does not make it through the first MOSFET. 20V is present on the drain of the first MOSFET, but there is no voltage on the gate or source.

When diagnosing this issue, I thought that the issue was due to the BQ24800 chip not outputting the correct signals so I soldered on a known working chip and the...

[Stunt]

Device: Laptop
Manufacture: Huawei
Model: NDZ-WFH9A
Motherboard: DAH98UMB8D0 REV D HF
Issue: Please help me and remove power on password

Attach my original bios.
Thanks in advance
[ATTACH]n3267210[/ATTACH] Device: Laptop
Manufacture: Huawei
Model: NDZ-WFH9A
Motherboard: DAH98UMB8D0 REV D HF
Issue: Please help me and remove power on password

Attach my original bios.
Thanks in advance
[ATTACH]n3267210[/ATTACH] ...

[dfresh1]

I would very much like to get a Latitude 3580 bios cleaned. Specifically the computrace reset to disabled.

Can't find anywhere on here for a Latitude 3580 except under this forum.

Model: Latitude 3580
ST: 4VH77F2
dfresh1...

[mist79]

I am still new to this, so I might sound brainless/ignorant in parts of my description/questions, since I have a lot of gaps in my knowledge, but I will do my best.

The laptop is Lenovo Legion Y540-15IRH, and the motherboard model is NM-C221 Rev 2.0 (Schematics and BoardView can be easily found). To save time I have the exact problem in the laptop as the one shown in this video:
[url]https://www.youtube.com/watch?v=tfucZ_WKpz4[/url]

I was checking the voltages I found that the main power rail V20B+ is good, and same for the +3VALW circut, but when I tried the +5VALW,...

[computeka]

How about everyone, I have a MacBook Air which did not turn on, it had a lot of corrosion on the card where the sound plug and the fingerprint go, I have replaced it and the device now turns on but has no sound, if I connect a headphone through the plug, yes There is sound but the external speakers do not sound....

[amirheidari681]

hi.
I want hp 450 g6 bios.
all of my voltages are present and it may be from the bios
SN: 5cd9227bc9
da0x8jmb8e0

I am not sure about my backup file...

[unimatrix93]

Can I ask you guys help me identify this godforsaken component?

I'm tearing my hair out finding this component.

The board is from an egg incubator.
i got it with a "popped cap" while there are many damaged components on it, which got succesfully identified with one exception:
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3267072}[/ATTACH]
And here is the board where it came from (U1/1):
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3267073}[/ATTACH]...

[ShocK-306HDi]

Hi friend, I've this notebook HP Gaming 16-a0006nl with QUANTA DAG3JBMB8D0 that won't power on.
I start checking first mosfet and they seems to be ok.
On power button I get 3 that go to 0 on pressing, and come to 3v on release.
After I check charge ic that is BQ738H
I write here measure with battery and ac

19
19
19
25
3

1.9
0
3.1
3.1
1

11
11
11
gnd
0

6
10
11
11
19

I've 0 on pin 7 IOUT and on pin 15 LODRV.
...

[cetincet]

fg542 fg543 fg742 nm-c101 rev 1.0 motherboard code. no image. I am giving the original bios copy, please correct it. The laptop label has been removed, there is no serial number. The bios given on the site was tried but no image could be obtained. CPU RYZEN 5...

[Gbolahan John o]

GOODDAY SIRS, PLEASE HELP ME UNLOCK GOOGLE ENROLLMENT FOR ACER CHROMEBOOK 13

MODEL: CHROMEBOOK 13 CB5-311-T7LG
S/N: NXMPREK003510118C13400
SNID: 51007187334...

[moheat]

[U]Hardware Details - Samsung LC24FG70FQWXXL (C24FG70) Monitor with the board model (BN91-18169A) perhaps aka (BN41-02548A)[/U]

While wall mounting, I mistakenly picked a screw 0.5cm too big than the clearance and damaged the trace and one of the part (a capacitor, I think) on the board. Images attached.

Is this repairable or will I just have to get the entire board replaced? Please guide about this.[U]Hardware Details - Samsung LC24FG70FQWXXL (C24FG70) Monitor with the board model (BN91-18169A) perhaps aka (BN41-02548A)[/U]

While wall mounting, I mistakenly

[modtool]

Dear collegues,
the owner of this machine brought it to me saying that suddenly one day the display didn't turn on anymore, he tought that all the machine was damaged but it turned out that the MacOS starts good and stays on, and that connecting it to an external display it works without problems.
If you take a look into general settings, you can also see that the internal retina display is recognized as connected by the main board but for an unknown reason it doesn't turn it on.
I've tried to put a bright light towards the screen but I can't see anything, any shadows or apple...

[YellowJacket]

Hi folks.
Any help with identifying this IC? Should be some DC/DC step down converter. 'ACF G45' ... I thought, it is Monolithic Power Systems ( based on this topic --> [url]https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/80630-ic-marking-codes-and-datasheets[/url] ), but can't find this marking there. Will be thankful for any hint. Thanks in advance.https://Hi folks.<br /> Any help wit... Power Systems...

[epoy]

Heres the old files (not sure if original)...

[aminsab]

Not Turning on

Serial : CND0296SP2...

[bigboots]

Need some help to identify this laptop ic please....

[pooya_pm]

AMD CPU
TYPPE: 20XH-SIT019
SERIAL NUMBER :PF-2J639V
BIOS & EC 32MB PLEASE...

[Yehuda170]

HP Spectre x360 - 13-aw0019nw DA0X3AMBAG0

do you have U6102 PD [URL="https://***********/tags/rom/"]ROM[/URL] of TPS65988DJ it's should be 1MB? or TPS65988DJ 1MB ROM from other boards?

before me the chip was killed by other tech, it was only 5v looping. after I soldered a new chip with TPS65988DH ROM it goes to 20V but looping after 10sec. I need TPS65988DJ dumpHP Spectre x360 - 13-aw0019nw DA0X3AMBAG0

do you have U6102 PD [URL="https://***********/tags/rom/"]ROM[/URL] of TPS65988DJ it's should be 1MB? or TPS65988DJ 1MB ROM from other

[IMLJ]

Hi,

Anyone please help me to unlock this bios.
HP PROBOOK 435 G10
SN:5CG3343FTQ
Many thanks....

[tktrom]

Good afternoon, I need the diagram and boarview for the board Lenovo GV453 NM-D121 rev: 1.0.
thank you so much.

[dd10]

I need bios for HP Z420 v2 witch Boot Block Ivy Bridge processors...

[feliks912]

Attached schematic 🙂.

Laptop gives no signs of life. No fan and no CPU heat.

Think Engine BD4179MWV is hot on plugging in *AND* pressing the power button.

Discovered short to ground on VCC5M power delivery IC NB690GRP (5 volt line, not the high current VCC5M_PD) which is one of the ways that chip is powered. I'm puzzled.

Nothing else is warm on the board. CPU resistances are OK, 9V VSYS line is present from the BMIC. All misc and cables are disconnected.

What do you guys think happened? I've got two theories:

If the...

[ub6ib969]

Hi,

working on a ASUS ROG STRIX GL702VSK 60NB0DZ0-MB1260 that does not power on. At the PQ8900 PIN2 (P_CHG_ACMOS_G_20) I am receiving 24.7V and PIN1 (P_CHG_ACMOS_S_20) 20V, however when I place the PQ8901 P_CHG_ACMOS_G_20 it drops 0V. I don't have the replacement mosfets ( N-MOSFET QM3058M6AC PRPAK5*6
UBIQ) however will any N-channel mosfet with similar parameters work ? I also found that PCI8703, PCI8701 are shorted. any help would be grateful.

[estabilito]

Hello, i bought dead nintendo switch oled.
after plugging charger with amp meter device shows 5v and 0,0 or 0,02 amperage draw.
I inspected motherboard and someone tried to reflow or replace m92t36 and didn't do it well, i resoldered it proper and find that usb-c fuse was blown too(replaced it).
After this device started to draw 15v and something around 0,48 but only for few seconds after this returned to 0A draw.
I tried to plug motherboard without battery - shows 15 0A and when charger was pluged i put battery back in then console started to charging battery but stuck...

[bigboots]

Hi all
Would like some help to identify this ic please. I cannot find a schematics for the board.
Thanks in advance.

[LEEDASH]

Hello all, Aiwa TX-110 Tuner got out of storage and the buttons was held in by some gloop, What glue would you use to restick these buttons (they are no snapped off)

Thank you

[CraigR]

I have a 12v psu from a DJ lighting system and I can not seem to figure this one out. The board so far had a blown fuse and a shorted voltage regulator. After replacing those I get 12v out but hooking a load to it the voltage seems to bounce between 5v and 0v. I remove all the caps and checked those and replaced 2 that were only questionable. I know it's not the device I connect it to as I put 12v to it with my bench power source and it works fine....

[almarhum]

Has one here really gone through fixing laptop screen vertical line(s) by repairing/replacing its Embedded DisplayPort (EDP) cable, so would recount and share the complete steps of the process here now?

As most, if not all, believe the laptop screen vertical line(s) caused by defective Embedded DisplayPort (EDP) cable which slipped and passed through either laptop screen hinge but post here is asking help to elaborate definitively the useful, real knowledge of repairing in the most complete, correct way, esp. can decide/determine whether the cable can still be fixed or must be re...

[nabilgo]

hi

need bios for toshiba portege r30-a part no pt343u borad number FASRSY1 A3688A

the old bios stat but no data...

[teruger]

Hello guys

My laptop have a FAN issue, i tried with a new FAN but the issue persist.
The motherboar is LA-G714P

I measured the JFAN1 connector

pin 1: 5v
pin 2: 0v FAN1_PWM
pin 3: 3v FAN1_TACH (this pin should not be 0v if the fan is off??)
pin 4: GND

Tanks for advance!

[moscast]

Hi everyone, I have the same problem with two Dell notebooks. One has the EDC41 LA-G891P motherboard and the other has the EDC50 LA-901P motherboard. Both do not turn on and the processor also heats up a little.
In the coils there are 3.3v - 5.1v - 13v - 19v - 1.8 - 1.05V and 1.0V prime core
On both notebooks, if I press the power button the LED turns red and if I release the button the LED turns off.
What could I still check before saying the processor is dead?
Thank you

[mferna14]

I am working on ACER Aspire A515-54-74LM Serial # NXHNAAA00693913C647600 (SNID: 93908099676 ). Motherboard DA0ZAWMB8G0 Rev.G (UMA, no video chip on this board). It turns on fine but when booting to Windows 11, it just keep loading. The Windows ring is continously spinning & does not proceed anywhere. I tried with another known good SSD Card with 100% Windows 11 bootable from this SSD., & result if still the same. BIOS ME Region has been cleaned, same result with old & new BIOS bin files. No Liquid spill anywhere on the main motherboard or the SSD Connector. What is the next step I...

[osbln]

Hello,


i am searching for schematics and boardview for NM-E791

unfortunately I could not find anything here in the forum

Thank You

[Techboxcomputer]

This has happened on three keyboards, so now I am assuming it is something in the machine but I can't track it down. Every time you plug in a logitech wireless keyboard it will immediately switch the "c" and the "v" permanent on these boards. There is no malicious software I can find, the board cannot be reset or put back. The very last one I tried was a MK 235 with the same end result. If you plug in a Microsoft wired comfort curve board, no problem at all. I have tried cleaning the system, deleting all boards from the device manager, updating the Logi software,checking MS...

[the Benninger]

dont work, only 3 asterics on lcd

It seems like a BIOS problem in the support of the page they have to update from Windows, but this is not even recognized as a device on the computer, I am looking for help I think you can rewrite the NAND memory again but I don't have the accessory

If anyone with a sililar case or experience has something to comment on, it is welcome

[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3266527}[/ATTACH]

Unfortunately they provide a *.fls...

[niconetor]

Hi! I have a corrumpt bios for this laptop

Model: Toshiba Satellite L50-A-14K
Motherboard: tmt YA-4A1 E114139 Rev 2.1
H000057570

No power, only led charging

This laptop have got two winbond
25q32fvsiq and 25q16dvsig

Thanks for all reply!

[salah11]

hello,
need bios dump for asus fx570u
attached the original bios,
the computer run and enter bios, but not windows boot
and the problem is that all the bios parameters are jamed
thank you

[Squaryhead]

Hi,
I'm struggling to find a software to reconfigure a GD 25LB128 chip with a CH341 A.
Do you know any ?
Thanks !

[grimacelord]

This laptop is the same laptop I was working on [URL="https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/bios-requests-only/3262622-hp-14-dq0055dx-bios-problem-pending-image-being-cleared-loop"]in this thread[/URL] and I wasn't sure if I should post a new topic or post in that thread because I already solved the issue that thread was discussing and this is a completely different issue although it is dealing with the same laptop. I decided to make a new thread since it's a new issue, but please move...

[amirheidari681]

Hi my friend,
I have ASUS r1605za and it's keyboard worked out after about 10 min.
I think the problem is related to bios.
can any body help me and correct my backup file?
( I have the same problem on another ASUS laptop and I fix it with correct bios file.)
sn: NBN0CV043681455...

[krsta]

Hi guys, hope someone could direct me in right way.

So i got the ASUS ROG THOR 1200W PLATINUM for 15€.

The first time i plugged it in wall socket there was no 5VSB present, so i disassembled it took a little peak inside and left it on shelf for a day.
Next day the 5VSB was present and the psu worked the whole day (outside of computer, shorting PS_ON to ground).
I tested it for a few days like than and then installed in my computer, it worked flawlessley for 1 month.(gaming and such for a few hours).

Few days ago i left it torrenting and saw...

[vpower]

Hi, I have this laptop, it is completely dead, no charging light when connected to a working charger.
Can anyone help me with some hints for troubleshooting this laptop?
Thanks in advance...

[appie1206]

Hello there friends

Can someone Clear this bios file for me ?
serialnumber: 5CG33778XV
productid: 709Z1AV

Thanks in advance...

[NiroPall]

Hello friends,
Please share this schematic if you have,
EPK50 LA-G07EP REV: 2.0 (HP)

Thank you.

[ImpossibleRepairs]

Hi Good peoples;

Been working on a turtle beach Velocity one flight controller; The slide pot for the throttle (black) isn't calibrating properly, it will register the axis with some wriggle until pressure is released;

Does anyone know the specifics for these Potentiometers?? I have attached photos;

Board number is LBX-19500，
C-V1.1 202011

please and thanks as always

[Comp_Pro]

Hello all,

Am trying to figure out this backlight issue with this A1990 Macbook Pro.

Tests performed:

There is no backlight even with a good screen.
Backlight IC is receiving the correct support voltages.
Fuse F8400 ok
Current sense resistor R8400 ok
Backlight IC is receiving 3.3V on enable pin.
Backlight IC receiving voltage from PPBUS_G3H, aprox 12.5V.
Backlight IC receiving 5V from PP5V_G3S
Backlight IC BKLT_SCL and BKLT_SDA both measure 0.545V diode mode to ground
I2C_BKLT_SCL and I2C_BKLT_SDA both measure...

[fixxz]

Could you help me get the bios for this lenovo the card model is JS47A/JS57A/JS77A NM-E531 REV 1.0 I do not have the original file since the chip was damaged

[gjgib]

Hello, this might be embarassing since I consider it a dumb question but keeps me kinda stuck sometimes in my journey.

I want to know if there is any post in this forum which explains my questions. [B]A)[/B] [B]When, where and how do I know when X voltage line is input or output. Example: [/B]

[URL=filedata/fetch?id=3266119&d=1715040463][ATTACH=JSON]{"alt":"Click image for larger version Name:\timage.png Views:\t0 Size:\t151.9 KB ID:\t3266119","data-align":"none","data-attachmentid":"3266119","data-size":"thumb"}[/ATTACH][/URL]...

[techrefurbca]

Hi,

It is my first BIOS request here.
I have a bios-locked AUS M415D

ASUS X415DAP

[kk126]

Hello, I have a da0h9bmbcd0 card which had a liquid spill, there was an area in which corrosion damaged the power rails but it is almost undetectable to where they are connected, I looked for the schematic diagram of the equipment but it is not available so if you can help me I would appreciate help knowing which integrated part is the one that had the damage....

[PITERPENY]

there is no reaction, it hangs at 20 V/0A. There was a little corrosion in the u7650 area. Replacing the u7000 did not help. Tell me, what else could it be? PPBUS_G3H=12.9V
Flashing the bios with a clean region also did not work!

[atmega4]

please i need unlock BIOS unowhy Y13 2021
Production year : Aout 2021
Model : Y13G011S4EI
Motherboard : EM_IG116_200b_ene_F_V1.0...

[Mogli1476]

Hey @all,

my ipad Pro dont want to work anymore. I measured the incoming amps which is approx. 0.5A. Then I changed the Tristar IC and blow out some parts near this IC. Now I want to find the missing parts. Thats why i´m asking for the schematics & board view for this ipad pro.

Thank for your help!

Best regards, Mike