Boardview ASUS TUF GAMING B450-PLUS II R1.01

[noelia prieto]

Hola, estoy buscando el Boardview ASUS TUF GAMING B450-PLUS II R1.01, ser

[Rofix]

Hello everyone, I kindly wanted to ask you for advice, on this PC as soon as I connect the power cable without doing anything the part where the CPU, GPU is heated up, with the bench power supply it absorbs 600 mA, without battery, kindly since I'm here various coils almost short what can we start doing? thanks for any advice


[ATTACH=JSON]{"data-align":"none","data-size":"full","title":"Asus 1.jpg","data-attachmentid":3268046}[/ATTACH]Hello everyone, I kindly wanted to ask you for advice, on this PC as soon...

[chth96]

I want to replace samhwa RG 250v 1uf capacitor which has no ESR value and has capacitance less than 280pf.
It is possible to purchase WCAP-ATG5 in local electronic shop.
But I want to know that whether WCAP-ATG5 capacitor has similar or better quality than smahwa capacitor or not.
Is there anyone who has experience to replace any bulge or faulty cap with cap from Wurth Elektronik?
[url]https://www.we-online.com/en/components/products/WCAP-ATG5[/url]https://I want to replace samhwa RG ...It is possible

[corrize]

[FONT=Calibri]Hello, I want to buy BGA balls (not stencils, only balls) but I don't know what size, it's just for reballing the new chip balled if the first attempt fail. So I will rarely use it. Probably chips are PMIC with max 60 balls. I don't need to reball EC chips from laptops of big chips like that.[/FONT]
[FONT=Calibri]So what are the 2 or 3 most used BGA balls sizes I should have for cover the jobs please ?[/FONT][FONT=Calibri]Hello, I want to buy BGA balls (not stencils, only balls) but I don't know what size, it's just for reballing the new chip balled if the first attempt fail.

[abajor]

I have a A2141 which fails DFU with error code shown in image.
Now instead of DFU it says "Recovery"

A little back ground on this laptop. I was thinking of writing a topic on corporate laziness and irresponsibility.
We acquired a handful of laptops which a very large company wanted to have shredded due to sensitive information.

Since apple has NSA grade drive formatting I think this is inexcusably lazy that the IT department doesn't just target mode format the drives and release the MDM, and donate the laptops.
Personally I think a large company...

[Traptor]

Hi guys,
I have a Gigabyte GTX 1080 G1 Gaming 8GB gpu. The earlier life of this gpu is unknown.

Fans are spinning on full speed.
All main voltages presents but gpu not detected by motherboard.
The voltage on pin 1 of the bios is constantly 1.8V

During visual inspection i noticed a brown spot on the top of the chip.
Maybe burned this GPU?

Does anyone have an idea where I should go next?
How do I check if the GPU is still alive?
[URL=filedata/fetch?filedataid=336585][ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3267995}[/ATTACH][/URL]...

[MicroSMD Lab]

This laptop came in as no internal display. I did see it boot on an external monitor but it was not consistent, however, the bios splash screen was consistent. The customer said it happened after a windows update. I tested the display and there were no signals on the LED_EN or PWM test points. At this point I decided to treat it as a bios issue. I disconnected the RTC battery and drained the residual power. After this, I did not get the bios splash screen anymore. The power led changes colour, fans spin, GPU and CPU get warm and caps lock is functional. I tried the bios from the Clevo repo, there...

[PITERPENY]

Hi all ! I really need help with my motherboard! consumption 20V / 0.060-0.280 A is unstable! not detected in DFU! There is no picture on either the external or internal monitor!
PPBUS_G3H=12,61v
PPBUS_HS_CPU=12.61v
PPDCIN_G3H=19.94v
PP5V_G3S=5.12v
PP5V_S5_LDO=5.12v
PP3V3_G3H_RTC=3.3v
PP3V3_G3H=3.3v
PP3V3_G3SSW_SNS=[B][COLOR=#c0392b]2.3-2.6v[/COLOR][/B] is unstable!
PP3V3_G3S=3.3v
PP3V3_TBT_X_S0=[B][COLOR=#d35400]0v[/COLOR][/B]
PP2V7_NAND=2.513v
PP1V8_G3S=1.8v
PPVCC_S0_CPU=[B][COLOR=#d35400]0v
[/COLOR][/B...

[digtalhd]

Any help with
Lenovo ThinkPad L13 Gen 1
Serial: R9117ESC
EC: 256KB
Plz remove password.
Thank you....

[roshon]

does anybody have Schematic and board view [B]Mac Mini 2018 model A1993 MLB 820-00939-A - does not boot, [/B]does anybody have Schematic and board view [B]Mac Mini 2018 model A1993 MLB 820-00939-A - does not boot, [/B]

[spleenharvester]

I bought one of [URL="https://www.aliexpress.com/item/1005002890887241.html"]these [/URL]as it was the only one I could find that is compact enough to fit in my toolbox (though I've since found [URL="https://www.aliexpress.com/item/32844169715.html"]KSGER make a substantially safer looking one[/URL]). It's one of those fan-in-handle things that has the 230V element in the handle. Quecoo briefly sold a [URL="https://www.aliexpress.com/item/1005004884759470.html"]similar unit [/URL]but discontinued it.. maybe they couldn't find solutions to these problems. I'm aware...

[gseeley]

Does anyone have a schematic for an HP ProDesk 400 G6 SFF main board?

I have one that blinks RED 5 times, pause, WHITE 7 times and repeats. This sequence isn't covered in the service guide. The closest is a memory issue but the one SODIMM is known/tested GOOD in another box (same model).

There looks to be some resistors(?) missing near BIOS flash chip.

[Luís Amaral]

Hello guys, i am working on a X512FF motherboard that comes dead, 19V stops on first mosfet, Gate only have 3v... if a make a bypass laptops works great with no problem... already tested the 5 mosfets, if i remove the current sensor PRS8901, the 19v appear...
Something with the 19V line and the charger detects and stop working !


Any advices ?...

[bociub]

Hi There

So I am looking for a part. Namely, a QqEEH. I beleive this is responsible to create the 3.3 power rail, but on my motherboard it is shorted to the ground. injecting 1 volt into the 20 volt power rail the IC heats up. Around the IC almost everything is shorted to the ground,
Anyone knows what this little controller chip supposed to be?

Thanks,...

[Ado02]

Hi,

I'm currently experiencing issues with my Dell Inspiron 5415. Initially, the laptop would sometimes fail to boot, with the keyboard backlight turning on but no display on the screen. After repeated attempts to power it on and off, it would eventually boot up and function normally.

To troubleshoot, I removed both the main battery and the BIOS battery, but now the laptop exhibits a different issue: the fan runs at full speed, but the screen remains blank, and it doesn't boot up.

I suspect there might be a problem with the BIOS, and I would like assistance...

[ductranvinh]

i have problem with vcore on this product then i need boardview to repair.
Model: Prime H410M-CS
Brand: Asuck...

[angelos]

Hi guys,
A few days ago i asked a real hard question regarding plasma tv's but nobody could respond. I need to ask if anyone has replaced this IGBT with another type that actually worked.
The industry is awash with fake chinese knock offs.
I am so frustrated.
Kind Regards
A Anagnostou

[saeidp9]

Boardview and Bios AIO Asus ET2020A

[jm1234]

Hi, I'm seeing one 9V relay having temperature 40C on its 9V (primary) side. Does that seem right? I switched 2 relays on that board and the temperature was the same (on the same position), so I'm sure it's not a faulty relay. I measured voltage on that relay and it was 9.5V DC, so that looks good. I don't see any other relay on that board having that kind of temperature and they have 9V on them too.
I thought maybe the transistor that is switching this relay keeps switching on/off, so I also checked for AC and there was almost none: 0.3V using mV range. No steady frequency was shown, but...

[Awsan]

Hello everyone, Due to a bad bios flash this Omen has a weird issue.

In the BIOS it says the ME version is 0.0.0.0 and when I try to update the BIOS it writes the bios region but when it reaches the firmware and ME it says it failed.

Tried HP USB recovery way and nothing worked.

I am kinda stuck, the main problem right now is the laptop would boot within 5 mins until the ME drivers load in windows and all works normally....

[riparo]

Hi everyone, I have a problem with a Samsung TV model UE50NU7400, I don't have the stanby LED, on the power supply board after a first check I found the fuse blown, and the 2 KF7N50 transistors on the primary power supply both short circuited, I replaced the fuse and the 2 transistors, now the short circuit has disappeared but I still don't have the LED off, do you have any suggestions?...

[samstown]

Hello,

This special tool from Apple is used to recover data from Macbook A1706. I've been using it for a while but it stops working. When connecting Thunderbolt 3 between the tool and working Macbook, Macbook should prompt "new device detected, allow or not"... but it doesn't.

Has anyone ever experience this ? It's not a cabling or power supply issue, some IC have stopped working but not sure which one. Probably the one that manager thunderbolt 3

Thanks
Claude...

[Biostechnology]

can u help someone nm-c121 tested bios...

[ImpossibleRepairs]

Hi Good peoples;

trying to identify manufacturers of this slide Pot from a Flight controller;

there is also an S W or M S printed underneath;

Sorry I couldn't get a better picture;

please and thanks as always

[Aleixpaolo]

Hello, please, could someone help me with my password problem with an asus F15- tuf 506H?

serial number : R1NRCX06Z23205A
full model machine : TUF506HC-HN088
board number : DAONJJMBAGO rev.G

Thanks in advance

[Ihandyrepair]

Hi

working on a not turning on Wheelspeed WS1 scooter.
diagnosed - issue is the display/power button

on the board, with the multimeter I noticed there is a short to ground. as the red wire has 0 ohm to ground.
with infrared camera, this chip (photo circled) would heat up if I push power button on.
but I can't find any replacement or online info of this chip.
on the chip you can see it has a label GM2H, I have another good working display with the same chip but it has label GM2C

could anyone help me id this chip and guide me to...

[ReparaPC]

I have an RTX 2070 Super from evga with a blown up IC. With the IC on the card, pin 17 had a short to ground. This pin is connected to the 5V rail by R993, a 0hm resistor. I removed both U610 and R993, to discover that the 5V rail has 800 Ohms of resistance to ground. After checking some resources online, i found a picture which describes the usual measurements a Turing series GPU should have in order to "work properlly". Interestingly enough, this gpu doesn't have U31, the IC responsible for the creation of the 5V on the card, as well as no L47.

Are these 800 ohms rigth...

[tommy97]

Hi, I've got bulk of lenovo l480 (joblot), all of them comes with bios password I'm looking for a good and reliable solution as we have loads of them, I do have SVOD 4 with keyboard connector, I haven't dealt with KBC PW yet and in my knowledge that's the case.

[learnmore]

Hi Community,

I've got the above model that activates the relay (clicks) and powers on the LG logo power light on when turned on. It then almost immediately turns off. I not noticed any image on the screen or heard any sound during this brief period.

Checks show:
3.5v on SMPS on (in off state, no other voltages present incl pwr on)
On pressing power button > the 3.5 pwn on voltage, 12v and 24v lines appear on the SMPS connnector between the main the SMPS but then all drop the zero in 1-2 seconds
Disconnecting 24 to TCON connector and powering on shows...

[steveoski]

Hey guys looking for the Bios for an Asus ROG G713PV-DS94
Motherboard Number is g713p-mb-VGT 6050A3468901-MB-A01
Serial Number is R3NRKD03613412E

i am not sure if any additonal information is needed if so let me know and i can update this post. Things i have tried are to download the BIOS directly from Asus but that file is a .329 file and is 32MB as opposed to the 16MB file i need. Scoured high and low and cant find this darn BIOS anywhere! Much appreciated!!...

[ResoluteHawk]

I have an Asus G14 (GA401QM) that has a power issue. Originally the board had a shorted 5V rail and dead EC. I reballed a working EC, soldered it on, and I resolved the 5V issue by replacing the APL6012 and the low side 5V mosfet. Resistances on all power rails are healthy now, but 20V does not make it through the first MOSFET. 20V is present on the drain of the first MOSFET, but there is no voltage on the gate or source.

When diagnosing this issue, I thought that the issue was due to the BQ24800 chip not outputting the correct signals so I soldered on a known working chip and the...

[Stunt]

Device: Laptop
Manufacture: Huawei
Model: NDZ-WFH9A
Motherboard: DAH98UMB8D0 REV D HF
Issue: Please help me and remove power on password

Attach my original bios.
Thanks in advance
[ATTACH]n3267210[/ATTACH] Device: Laptop
Manufacture: Huawei
Model: NDZ-WFH9A
Motherboard: DAH98UMB8D0 REV D HF
Issue: Please help me and remove power on password

Attach my original bios.
Thanks in advance
[ATTACH]n3267210[/ATTACH] ...

[dfresh1]

I would very much like to get a Latitude 3580 bios cleaned. Specifically the computrace reset to disabled.

Can't find anywhere on here for a Latitude 3580 except under this forum.

Model: Latitude 3580
ST: 4VH77F2
dfresh1...

[mist79]

I am still new to this, so I might sound brainless/ignorant in parts of my description/questions, since I have a lot of gaps in my knowledge, but I will do my best.

The laptop is Lenovo Legion Y540-15IRH, and the motherboard model is NM-C221 Rev 2.0 (Schematics and BoardView can be easily found). To save time I have the exact problem in the laptop as the one shown in this video:
[url]https://www.youtube.com/watch?v=tfucZ_WKpz4[/url]

I was checking the voltages I found that the main power rail V20B+ is good, and same for the +3VALW circut, but when I tried the +5VALW,...

[computeka]

How about everyone, I have a MacBook Air which did not turn on, it had a lot of corrosion on the card where the sound plug and the fingerprint go, I have replaced it and the device now turns on but has no sound, if I connect a headphone through the plug, yes There is sound but the external speakers do not sound....

[amirheidari681]

hi.
I want hp 450 g6 bios.
all of my voltages are present and it may be from the bios
SN: 5cd9227bc9
da0x8jmb8e0

I am not sure about my backup file...

[unimatrix93]

Can I ask you guys help me identify this godforsaken component?

I'm tearing my hair out finding this component.

The board is from an egg incubator.
i got it with a "popped cap" while there are many damaged components on it, which got succesfully identified with one exception:
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3267072}[/ATTACH]
And here is the board where it came from (U1/1):
[ATTACH=JSON]{"data-align":"none","data-size":"medium","data-attachmentid":3267073}[/ATTACH]...

[ShocK-306HDi]

Hi friend, I've this notebook HP Gaming 16-a0006nl with QUANTA DAG3JBMB8D0 that won't power on.
I start checking first mosfet and they seems to be ok.
On power button I get 3 that go to 0 on pressing, and come to 3v on release.
After I check charge ic that is BQ738H
I write here measure with battery and ac

19
19
19
25
3

1.9
0
3.1
3.1
1

11
11
11
gnd
0

6
10
11
11
19

I've 0 on pin 7 IOUT and on pin 15 LODRV.
...

[cetincet]

fg542 fg543 fg742 nm-c101 rev 1.0 motherboard code. no image. I am giving the original bios copy, please correct it. The laptop label has been removed, there is no serial number. The bios given on the site was tried but no image could be obtained. CPU RYZEN 5...

[Gbolahan John o]

GOODDAY SIRS, PLEASE HELP ME UNLOCK GOOGLE ENROLLMENT FOR ACER CHROMEBOOK 13

MODEL: CHROMEBOOK 13 CB5-311-T7LG
S/N: NXMPREK003510118C13400
SNID: 51007187334...

[moheat]

[U]Hardware Details - Samsung LC24FG70FQWXXL (C24FG70) Monitor with the board model (BN91-18169A) perhaps aka (BN41-02548A)[/U]

While wall mounting, I mistakenly picked a screw 0.5cm too big than the clearance and damaged the trace and one of the part (a capacitor, I think) on the board. Images attached.

Is this repairable or will I just have to get the entire board replaced? Please guide about this.[U]Hardware Details - Samsung LC24FG70FQWXXL (C24FG70) Monitor with the board model (BN91-18169A) perhaps aka (BN41-02548A)[/U]

While wall mounting, I mistakenly

[modtool]

Dear collegues,
the owner of this machine brought it to me saying that suddenly one day the display didn't turn on anymore, he tought that all the machine was damaged but it turned out that the MacOS starts good and stays on, and that connecting it to an external display it works without problems.
If you take a look into general settings, you can also see that the internal retina display is recognized as connected by the main board but for an unknown reason it doesn't turn it on.
I've tried to put a bright light towards the screen but I can't see anything, any shadows or apple...

[YellowJacket]

Hi folks.
Any help with identifying this IC? Should be some DC/DC step down converter. 'ACF G45' ... I thought, it is Monolithic Power Systems ( based on this topic --> [url]https://www.badcaps.net/forum/troubleshooting-hardware-devices-and-electronics-theory/troubleshooting-laptops-tablets-and-mobile-devices/80630-ic-marking-codes-and-datasheets[/url] ), but can't find this marking there. Will be thankful for any hint. Thanks in advance.https://Hi folks.<br /> Any help wit... Power Systems...

[epoy]

Heres the old files (not sure if original)...

[aminsab]

Not Turning on

Serial : CND0296SP2...

[bigboots]

Need some help to identify this laptop ic please....

[pooya_pm]

AMD CPU
TYPPE: 20XH-SIT019
SERIAL NUMBER :PF-2J639V
BIOS & EC 32MB PLEASE...

[Yehuda170]

HP Spectre x360 - 13-aw0019nw DA0X3AMBAG0

do you have U6102 PD [URL="https://***********/tags/rom/"]ROM[/URL] of TPS65988DJ it's should be 1MB? or TPS65988DJ 1MB ROM from other boards?

before me the chip was killed by other tech, it was only 5v looping. after I soldered a new chip with TPS65988DH ROM it goes to 20V but looping after 10sec. I need TPS65988DJ dumpHP Spectre x360 - 13-aw0019nw DA0X3AMBAG0

do you have U6102 PD [URL="https://***********/tags/rom/"]ROM[/URL] of TPS65988DJ it's should be 1MB? or TPS65988DJ 1MB ROM from other

[IMLJ]

Hi,

Anyone please help me to unlock this bios.
HP PROBOOK 435 G10
SN:5CG3343FTQ
Many thanks....

[tktrom]

Good afternoon, I need the diagram and boarview for the board Lenovo GV453 NM-D121 rev: 1.0.
thank you so much.

[dd10]

I need bios for HP Z420 v2 witch Boot Block Ivy Bridge processors...

[feliks912]

Attached schematic 🙂.

Laptop gives no signs of life. No fan and no CPU heat.

Think Engine BD4179MWV is hot on plugging in *AND* pressing the power button.

Discovered short to ground on VCC5M power delivery IC NB690GRP (5 volt line, not the high current VCC5M_PD) which is one of the ways that chip is powered. I'm puzzled.

Nothing else is warm on the board. CPU resistances are OK, 9V VSYS line is present from the BMIC. All misc and cables are disconnected.

What do you guys think happened? I've got two theories:

If the...

[ub6ib969]

Hi,

working on a ASUS ROG STRIX GL702VSK 60NB0DZ0-MB1260 that does not power on. At the PQ8900 PIN2 (P_CHG_ACMOS_G_20) I am receiving 24.7V and PIN1 (P_CHG_ACMOS_S_20) 20V, however when I place the PQ8901 P_CHG_ACMOS_G_20 it drops 0V. I don't have the replacement mosfets ( N-MOSFET QM3058M6AC PRPAK5*6
UBIQ) however will any N-channel mosfet with similar parameters work ? I also found that PCI8703, PCI8701 are shorted. any help would be grateful.

[estabilito]

Hello, i bought dead nintendo switch oled.
after plugging charger with amp meter device shows 5v and 0,0 or 0,02 amperage draw.
I inspected motherboard and someone tried to reflow or replace m92t36 and didn't do it well, i resoldered it proper and find that usb-c fuse was blown too(replaced it).
After this device started to draw 15v and something around 0,48 but only for few seconds after this returned to 0A draw.
I tried to plug motherboard without battery - shows 15 0A and when charger was pluged i put battery back in then console started to charging battery but stuck...

[bigboots]

Hi all
Would like some help to identify this ic please. I cannot find a schematics for the board.
Thanks in advance.

[LEEDASH]

Hello all, Aiwa TX-110 Tuner got out of storage and the buttons was held in by some gloop, What glue would you use to restick these buttons (they are no snapped off)

Thank you