Announcement

Collapse
No announcement yet.

KDL-55hx800 has 6 blink code

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    KDL-55hx800 has 6 blink code

    This set will run for about 5 minutes then shut off and the standby light blinks 6 times then repeats. I can press the power button and it comes back on but for a shorter time. I have the service manual and in the flow chart I am supposed to check the voltage at JL2565 to determine if the bal board or tcon failed. Does anyone know where JL2565 is located since I have looked and can not find it.
    Attached Files

    #2
    Re: KDL-55hx800 has 6 blink code

    How about uploading the service manual you have? or the link to it?
    Never stop learning
    Basic LCD TV and Monitor troubleshooting guides.
    http://www.badcaps.net/forum/showthr...956#post305956

    Voltage Regulator (LDO) testing:
    http://www.badcaps.net/forum/showthr...999#post300999

    Inverter testing using old CFL:
    http://www.badcaps.net/forum/showthr...er+testing+cfl

    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
    http://s807.photobucket.com/user/budm/library/

    TV Factory reset codes listing:
    http://www.badcaps.net/forum/showthread.php?t=24809

    Comment


      #3
      Re: KDL-55hx800 has 6 blink code

      I will in the morning when I get back into the store.

      Comment


        #4
        Re: KDL-55hx800 has 6 blink code

        Per service manual I found, 6-blink = Backlights Error, page 9.
        Attached Files
        Never stop learning
        Basic LCD TV and Monitor troubleshooting guides.
        http://www.badcaps.net/forum/showthr...956#post305956

        Voltage Regulator (LDO) testing:
        http://www.badcaps.net/forum/showthr...999#post300999

        Inverter testing using old CFL:
        http://www.badcaps.net/forum/showthr...er+testing+cfl

        Tear down pictures : Hit the ">" Show Albums and stories" on the left side
        http://s807.photobucket.com/user/budm/library/

        TV Factory reset codes listing:
        http://www.badcaps.net/forum/showthread.php?t=24809

        Comment


          #5
          Re: KDL-55hx800 has 6 blink code

          I see it is a backlight error but according to the service manual I need to check the voltage at JL2565 and I just can not find that. I am pretty sure all of the led's are good since it does work for 5 minutes but without checking for 2.65V at JL2565 I can not isolate which board it might be. Anyway I have attached the service manual and page 29 is where it looks for the 2.65V.
          Attached Files

          Comment


            #6
            Re: KDL-55hx800 has 6 blink code

            I am back trying to fix this tv and need some suggestions/help. I have checked the voltages on cn6753, 12v reads 0v GL-Error is 24v and all vled-vcc are 24v led-on is 3.3v. cn6152 standby is 3.3v, ac det off is 3.3v, power on is 3.25v, audio 12v is 12v, t-con vcc 12v is 12v, and t-con on is 3.25v. on the led driver board all 4 vcc led test points are 34v. If I unplug cn4002 from led driver the tv will stay on and never shut off. When I disconnect the lvds cable from the balance board I get a nice white background with no dead led's in the picture, it gets a little darker and I can see a bright led bottom center. It is really pronounced when the screen turns red then shuts off. I did send the balance board in for testing and it was fine. The service manual says change the G board next which I believe is the power supply but I don't think that is it and now I am wondering if maybe the led driver or t-con might be failing. I did freeze spray the led driver board and it made no difference. Bottom line is does anyone have and suggestions? And now as I am writing this the 12v on cn 6753 reads 0v and that is most likely the problem.
            Attached Files
            Last edited by nwcs; 12-21-2016, 05:46 PM.

            Comment


              #7
              Re: KDL-55hx800 has 6 blink code

              Hi I googled jl2565 and found this CN2561 at PIN 3. It is for different model but may help.
              I assume no responsibility for any stupid suggestions I might post.

              Comment


                #8
                Re: KDL-55hx800 has 6 blink code

                Thanks, I had also found that ant the voltage is at 3.3v so that leads to g board or tcon. at this point I am going to either order a power supply or the repair kit. Since I do not have the 12v I should be getting the 2 blink code with that missing. I am beginning to not trust the sony blink codes.

                Comment


                  #9
                  Re: KDL-55hx800 has 6 blink code

                  Hi @nwcs, did you find the fix for your issue? Was it the power Supplu? I have the same issue but with 4 blink red lights. My tv is 46HX800 very similar to yours.
                  Thanks

                  Comment


                    #10
                    Re: KDL-55hx800 has 6 blink code

                    The Sony KDL Service Manual is totally useless. I just ordered the repair kit from shop jimmy. Hope it fixes my KDL-55HX800. 2 blink code.

                    Comment


                      #11
                      Re: KDL-55hx800 has 6 blink code

                      So I replaced all the components in the repair kit and now the TV is worse. I cant even get the relay to switch.

                      Comment

                      Working...
                      X