Announcement

Collapse
No announcement yet.

Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

    Above TV, power on, 8 flashes tested all diodes and electrolytic caps ok
    voltages shown on attached photo's. LEDs tested all but one was open so I bridged open LED all light but very dim. Shining torch I can see text on screen but voltage low on led connector. I dont have a remote yet. Any help would be appreciated.

    Many thanks.
    Attached Files

    #2
    Re: Vestel 32" LED Smart TV

    Need to remove power board and look at the pins for leds for cracked joints. Common problem.
    I assume no responsibility for any stupid suggestions I might post.

    Comment


      #3
      Re: Vestel 32" LED Smart TV

      my guess a failed led dragging led voltage down.

      Comment


        #4
        Re: Vestel 32" LED Smart TV

        All but one of leds light this was open so I bridged it and all work but very dim would the single bridged led prevent the Pwm from working I wanted to see if the tv was working I would then buy new led strips.

        Comment


          #5
          Re: Vestel 32" LED Smart TV

          Most models (Samsung an exception) will shut down the LEDs if the voltage across the array is lower than expected (indicating shorted LEDs). If you want to test, put in a used LED module with same voltage drop.

          Comment


            #6
            Re: Vestel 32" LED Smart TV

            Hi guys sorry for late reply checked board no apparent dry joints.
            Can I use a resistor in place of bridged open led to correct voltages.
            If so what would be the resistance I assume these are 3v leds cannot find specs anywhere regarding voltages just says 3v or 6v nothing on strips.
            I have read that it may be a firmware problem. This is a Digihome 32" Smart TV.
            Vestel boards as shown in photos. 2 Led strips 11 on each strip wired in series.
            Many thanks.

            Comment


              #7
              Re: Vestel 32" LED Smart TV

              Originally posted by John McGivern View Post
              Above TV, power on, 8 flashes tested all diodes and electrolytic caps ok
              voltages shown on attached photo's. LEDs tested all but one was open so I bridged open LED all light but very dim. Shining torch I can see text on screen but voltage low on led connector. I dont have a remote yet. Any help would be appreciated.

              Many thanks.
              Put make and model number in thread title ! ! !

              https://www.badcaps.net/forum/showthread.php?t=24661
              All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

              Comment


                #8
                Re: Digihome PTDR32FHDS5 VES315UNDB-2D-N21

                Main board and power board numbers shown in attached photos. Cheers.

                Comment


                  #9
                  Re: Digihome PTDR32FHDS5 VES315UNDB-2D-N21

                  Originally posted by John McGivern View Post
                  Main board and power board numbers shown in attached photos. Cheers.
                  The TV model number.Can`t add a picture into the thread title
                  All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

                  Comment


                    #10
                    Re: Vestel 32" LED Smart TV

                    Sorry gents been away for a week.
                    SMDFlea Digihome Model~: PTDR32FHDS5 Made in Turkey.

                    Comment


                      #11
                      Re: Vestel 32" LED Smart TV

                      i doubt if its a firmware issue if the tv is turning on and backlights work too a point what is printed on the led stips also what lcd panel type is used in this set.

                      Comment


                        #12
                        Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                        Hi. LED number = VES315UNDB-2D-N21.
                        No LCD NUMBER I can see.

                        Comment


                          #13
                          Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                          Sorry for late reply sent to China for 2 new strips all lit but all dim.

                          Comment


                            #14
                            Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                            what voltage is on the led connector on the power supply did you get led strips that was 3v leds

                            Comment


                              #15
                              Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                              Hi, yes 3volt leds black wire 53.77vdc, red wire 1.68vdc

                              Comment


                                #16
                                Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                                Connect a video source to tv (hdmi or dvbt).
                                https://www.badcaps.net

                                Comment


                                  #17
                                  Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                                  54V/ 3V = 18 leds.

                                  Comment


                                    #18
                                    Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                                    Hi ther are 2 strips each strip has 11 Leds -22Leds = 66volts as previously said all lit but very dim.

                                    Comment


                                      #19
                                      Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                                      Is the power source original? If it is original, replace the circled capacitor.
                                      L.E.
                                      For backlight control, the processor commands the BL / ON pin. For intensity the processor commands the DIM pin, Measure on the dim pin if you find any voltage.
                                      Attached Files
                                      Last edited by yokoono; 04-14-2022, 09:38 AM.

                                      Comment


                                        #20
                                        Re: Digihome PTDR32FHDS5 (Vestel) 32" LED Smart TV

                                        No replaced power supply same symptom.
                                        No voltage on Dim pin.

                                        Comment

                                        Working...
                                        X