sony svf14 HK8 no power

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pc.heidari
    Member
    • Apr 2020
    • 14
    • Iran

    #1

    sony svf14 HK8 no power

    hi . i have a sony svf14 da0hk8mb6e0 rev e .
    no power
    main have 3.3 and 5 pcu . bios pin 8 have 3.3 .
    kbc chipset have 3.3 pcu and other .
    but on pwrbtn (nbswon ) are 0.3 v
    on kbc pwrbtn out ok
    lid sw ok
    rsmrst ok .
    bios check
    why no any voltage on power btn ? laptop dont power
    Attached Files
  • mayss
    Member
    • Nov 2016
    • 30
    • Polska

    #2
    Re: sony svf14 HK8 no power

    Make a short circuit of the KBC leg 15 (EC_PWRBTN #) to ground and see if the motherboard starts.

    Comment

    • pc.heidari
      Member
      • Apr 2020
      • 14
      • Iran

      #3
      Re: sony svf14 HK8 no power

      i have done this but no power . still on power btn no voltage .

      Comment

      • mon2
        Badcaps Legend
        • Dec 2019
        • 14484
        • Canada

        #4
        Re: sony svf14 HK8 no power

        Remove D1 diode and test again.
        Attached Files

        Comment

        • pc.heidari
          Member
          • Apr 2020
          • 14
          • Iran

          #5
          Re: sony svf14 HK8 no power

          d1 not on board . empty

          Comment

          • mon2
            Badcaps Legend
            • Dec 2019
            • 14484
            • Canada

            #6
            Re: sony svf14 HK8 no power

            What is the resistance to ground for NBSWON# on the switch ? Red meter probe on NBSWON# and black meter probe to ground.

            Confirm with the meter, that the switch is working. When you close the on/off switch, does the meter show close to 0 ohms ? I am assuming that the ON/OFF function is a simple mechanical switch for this design. Not sure if there is a logic board with the on/off switch.

            Comment

            • pc.heidari
              Member
              • Apr 2020
              • 14
              • Iran

              #7
              Re: sony svf14 HK8 no power

              resistance nbswon# with gnd are 7.6 m/ohm .

              Comment

              • mon2
                Badcaps Legend
                • Dec 2019
                • 14484
                • Canada

                #8
                Re: sony svf14 HK8 no power

                What is the resistance when you press the on/off button ?

                Comment

                Related Topics

                Collapse

                • Tynan Dill
                  Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                  by Tynan Dill
                  I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                  Upon bringing it home and plugging it up, it showed a standby light.

                  I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                  The screen seems to blackout and stay black, but with a flashlight I can see the display.

                  With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                  Assuming...
                  11-22-2024, 01:46 PM
                • GLISIT
                  Asus Probook P5440UF-XB74 power issue
                  by GLISIT
                  Hi all,

                  TL;DR - this laptop is driving me nuts with the oddball power-related behaviors. Appreciate any insight you can provide!


                  I'm experiencing a power issue on an Asus Probook P5440UF-XB74. Although I've worked with electronics and computers for decades, this is my first attempt at getting into motherboard-level component troubleshooting. Any help the community can provide is greatly appreciated!

                  A few weeks ago I was using the laptop (on battery power) for a Zoom meeting. The battery was running very low (long meeting) but I wasn't worried about...
                  01-16-2025, 02:29 PM
                • PopsCaps
                  Sony Bravia KDL-40V2500 that will not power on
                  by PopsCaps
                  I have a Sony Bravia KDL-40V2500 that will not power on. The indicator flashes red 3 times.
                  I do not hear any sound and I cannot see any backlight.
                  I have tried disconnecting every cable on each board one at a time to see if anything changes.
                  The only change is when I disconnect AC-DET cable on the Power Supply board or on the other end if I unplug the CN7009 connection on the B-Board and try to power on the TV the indicator will stay on solid green until I power off.
                  My friend ordered another used power supply board but it is also doing the red indicator flash 3 times...
                  03-25-2025, 11:23 AM
                • phuzzyday
                  Sony 70" 70X690E - It's now a divorce risk! (6 Months on kitchen table.) New power board installed! STILL trouble!?!?
                  by phuzzyday
                  For masochists who want to see some of the crap that I have been through already... (Truly optional now though, all those trees were barked up for no reason.)

                  https://www.badcaps.net/forum/troubl...klight-circuit

                  I started a new thread to get a fresher look at things, even with eyes that looked before. It's different now!

                  So I got this on Facebook for $66US, blank screen. Just reseated all...
                  09-08-2025, 05:53 PM
                • sam_sam_sam
                  Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
                  by sam_sam_sam
                  I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

                  One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
                  03-31-2024, 02:12 PM
                • Loading...
                • No more items.
                Working...