Ubiquiti Nano LocoM2. Not working, help

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • SoporteHR
    Senior Member
    • Sep 2018
    • 80
    • Venezuela
    #1

    Ubiquiti Nano LocoM2. Not working, help

    Hi all

    Receive a warm greeting

    I have a LocoM2 unit.

    I presume that the firmware is corrupted since when turning on the computer it does not do anything.

    ¿Someone will have the original dump version of this computer?

    I downloaded a firmware from the official page, but it did not work. Now turn on some LEDs but does not respond.

    Record the flash with the CH341 programmer, since it was impossible to connect via LAN / TFTP.

    LocoM2
    Board: FR494 V-0 / E88551
    Flash Chip: Winbond 25064CVF1G

    Thanks
    Attached Files
    Tags: None
    • CapLeaker
      Leaking Member
      • Dec 2014
      • 8340
      • Canada
      #2
      Re: Ubiquiti Nano LocoM2. Not working, help

      usually these things are purchased in pairs, also 2 of them at the same time. See if you can get the other unit, factory reset it, then copy the content. I haven't seen one that had corrupted firmware. If the winbond is good, I highly doubt the firmware is corrupt.
      what happens if you press the reset button? Make sure that button is good and not jammed (don't ask, I've seen that).

        Comment

        • SoporteHR
          Senior Member
          • Sep 2018
          • 80
          • Venezuela
          #3
          Re: Ubiquiti Nano LocoM2. Not working, help

          Hi.

          Thank you very much for your answer.

          I do not have the other unit, they only gave me this as a gift and for replacement, since it is practically dead.

          Turn on but there is no connection to the LAN. The LEDs do not respond as it should, nor does it respond to RESET procedures. Neither factory reset. That's why I think it's a firmware or memory problem.

          Thank you.

            Comment

            • CapLeaker
              Leaking Member
              • Dec 2014
              • 8340
              • Canada
              #4
              Re: Ubiquiti Nano LocoM2. Not working, help

              There are 2 different firmware's available for that LocoM2. Apparently there are 2 different boards. An XM and a XW board, each have their own firmware. Probe around the LAN port with an oscilloscope. Some LAN connectors have magnetics inside, or my best guess is the LAN chip itself is bad and needs replacing. Look at this example for an Atheros 7240: https://www.lan23.ru/forum/attachmen...0&d=1502374718
              Last edited by CapLeaker; 08-02-2019, 08:19 PM.

                Comment

                • Jonsered2050
                  New Member
                  • Sep 2019
                  • 1
                  • Elbonia
                  #5
                  Re: Ubiquiti Nano LocoM2. Not working, help

                  Simply connect a console (UART/whatever) cable and see how far it boots.

                    Comment

                    • MaXwELL
                      Member
                      • Oct 2009
                      • 14
                      • Turkey
                      #6
                      Re: Ubiquiti Nano LocoM2. Not working, help

                      CPU are bad
                      Change AR7240 or 7241 and working again.

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • gurj1979
                          Ubiquiti firmware help. US-8-150W POE
                          by gurj1979
                          Hi guys.

                          I've got a Ubiquiti US-8-150W POE switch which has issues with updating the firmware.
                          Turned out to be a bad EEPROM chip. It would read the firmware and work as normal, but failed to write new firmware to it.

                          So I took off the chip and read on EEPROM and saved it. Wrote to old chip and failed to write
                          Got New chip and writes good.

                          THE PROBLEM...
                          It fails to fully load the firmware, POE lights fail to work during g firmware test during load. I'm suspecting bad EEPROM Read.

                          Does anyone have a Good Firmware I can have?...
                          07-22-2024, 05:13 PM
                        • Document Archive
                          SHUTTLE XPC nano NC3000BA XPC nano 3865U Specification for Upgrade or Repair
                          by Document Archive
                          This specification for the SHUTTLE XPC nano NC3000BA can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the XPC nano NC3000BA boardview and XPC nano NC3000BA schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
                          09-12-2024, 03:36 PM
                        • Document Archive
                          SHUTTLE XPC nano NC1010BA XPC nano 4205U Specification for Upgrade or Repair
                          by Document Archive
                          This specification for the SHUTTLE XPC nano NC1010BA can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the XPC nano NC1010BA boardview and XPC nano NC1010BA schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
                          09-12-2024, 03:36 PM
                        • Document Archive
                          SHUTTLE XPC nano NC1010XA XPC nano 4205U Specification for Upgrade or Repair
                          by Document Archive
                          This specification for the SHUTTLE XPC nano NC1010XA can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the XPC nano NC1010XA boardview and XPC nano NC1010XA schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
                          09-12-2024, 03:36 PM
                        • zklgfs
                          Anker SoundCore 2 Bluetooth Speaker Turns Off After a Few Seconds (Possibly Firmware Issue?)
                          by zklgfs
                          Hi,

                          I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...
                          08-11-2025, 02:14 PM
                        • Loading...
                        • No more items.
                        Working...