Badcaps.net Forum
Go Back   Badcaps Forums > Troubleshooting Hardware & Devices and Electronics Theory > Troubleshooting TVs and Video Sources
Register FAQ Calendar Search Today's Posts Mark Forums Read

 
Thread Tools Display Modes
Old 10-02-2016, 08:39 AM   #1
Dannyx
CertifiedAxhole
 
Dannyx's Avatar
 
Join Date: Aug 2016
City & State: Constanta
My Country: Romania
Line Voltage: 230VAC 50Hz
I'm a: Hardcore Geek
Posts: 2,641
Question LG 32LX2R only 5V standby voltage (YP2632t PSU)

Good day folks. As the title says, I've got this YP2632T power board from an LG TV that won't power on. Couldn't find the schematic, so that would be greatly appreciated as well. The standby LED comes on, but that's about it....I removed the power supply and tried turning it on 'manually' by applying 5V to the ON/OFF pin (standard stuff): the relay clicks and the main cap C102 charges up to around 400V, but the secondary stays dead: no volts other than STBY. I could tell no "switching action" was going on because I couldn't hear anything AT ALL (SMPSs usually make a slight hissing sound when operating).
Many sources suggest replacing every single cap on the secondary, but I find it hard to believe that it would cause the board to turn on, since the problem is somewhere in the primary I believe. I DID replace the 3 small 47uF caps (C105 thru 107) that are part of the startup circuit and the 5VSB ones (C221-C222), but still nothing. SOMETIMES, I'd get 6v on the 12v bus, but nothing on the others, so it's like "half-working". I checked the 3 ICs in the primary: IC101, IC302 and IC303. The first 2 are FAN7601 MOSFET drivers. The last one (on the right in the picture (IC303) is a MIC4423. The first FAN (IC101) seems to operate normally, as it drives the standby circuit which puts out 5v accordingly. The second FAN (IC302) does get 10.4V on its VCC pin, but I don't know what it's supposed to drive after that, since its OUT pin doesn't go to one of the 2 remaining FETs like I expected, instead, it goes through a diode (D307) to the VCC pin of the MIC (IC303). Well, that pin is dead (no power). It seems to me the OUT of IC302 is rectified by that SMD diode and used as the supply for IC303...what a freak setup >_> This is also why I believe IC302 might be faulty and not putting out anything on its OUT pin, which in turn prevents IC303 from starting the switching action. Another mystery is how the second MOSFET (Q102) is driven, since its gate pin doesn't seem to go to any of the ICs - it loops back to the source through some resistors and diodes :|
To further make this more annoying and complicated than it should be, it's one of those bullsh!t double-sided boards which are extremely hard to follow and you have to keep flipping it around It seems a fairly common problem, but mine's a bit different that others I found. Any thoughts ? Let me know if you need close-ups of any other part of the board.
Attached Images
File Type: jpg 2016-10-02 001.jpg (838.1 KB, 50 views)
File Type: jpg 2016-10-02 002.jpg (720.5 KB, 39 views)
__________________
Wattevah...
Dannyx is offline   Reply With Quote
Old 11-18-2019, 06:15 AM   #2
jose almeida tavares
New Member
 
Join Date: May 2011
Posts: 1
Default Re: LG 32LX2R only 5V standby voltage (YP2632t PSU)

Hello, friend, the problem is solved? in this case the component replaced? thanks.
jose almeida tavares is offline   Reply With Quote
Old 11-18-2019, 06:33 AM   #3
nomoresonys
Badcaps Veteran
 
Join Date: Jan 2013
City & State: midwest
My Country: U.S.
I'm a: Knowledge Seeker
Posts: 4,228
Default Re: LG 32LX2R only 5V standby voltage (YP2632t PSU)

Ok, and what component was it??
nomoresonys is offline   Reply With Quote
Old 11-18-2019, 07:30 AM   #4
Dannyx
CertifiedAxhole
 
Dannyx's Avatar
 
Join Date: Aug 2016
City & State: Constanta
My Country: Romania
Line Voltage: 230VAC 50Hz
I'm a: Hardcore Geek
Posts: 2,641
Default Re: LG 32LX2R only 5V standby voltage (YP2632t PSU)

No, I don't think I managed to get it going, otherwise I would've posted the follow-up, unfortunately
Dannyx is offline   Reply With Quote
Old 11-18-2019, 07:42 AM   #5
nomoresonys
Badcaps Veteran
 
Join Date: Jan 2013
City & State: midwest
My Country: U.S.
I'm a: Knowledge Seeker
Posts: 4,228
Default Re: LG 32LX2R only 5V standby voltage (YP2632t PSU)

My bad Danny, I should have quoted jose almeida tavares, he said he fixed it but didn't explain what component it was.
nomoresonys is offline   Reply With Quote
Old 11-18-2019, 07:45 AM   #6
Dannyx
CertifiedAxhole
 
Dannyx's Avatar
 
Join Date: Aug 2016
City & State: Constanta
My Country: Romania
Line Voltage: 230VAC 50Hz
I'm a: Hardcore Geek
Posts: 2,641
Default Re: LG 32LX2R only 5V standby voltage (YP2632t PSU)

No, I don't think he fixed it - from what I understand, he asked the same thing
Dannyx is offline   Reply With Quote
Old 11-18-2019, 07:47 AM   #7
nomoresonys
Badcaps Veteran
 
Join Date: Jan 2013
City & State: midwest
My Country: U.S.
I'm a: Knowledge Seeker
Posts: 4,228
Default Re: LG 32LX2R only 5V standby voltage (YP2632t PSU)

Oh, lol, I see now, it was a question.
nomoresonys is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Badcaps.net Technical Forums 2003 - 2019
Powered by vBulletin ®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 08:02 AM.
Did you find this forum helpful?