|
|
|
|||||||
|
|
Thread Tools | Display Modes |
11-07-2021, 05:39 PM
|
#1 |
|
New Member
Join Date: Jun 2021
City & State: Cairo Governorate
My Country: Egypt
I'm a: Knowledge Seeker
Posts: 16
|
Can I bridge power good signal in my PSU?
Hello
I have a 1600 watt power supply that is not outputting 5V from pin8 (PGO) of ST9S313 ( which is a PC POWER SUPPLY SUPERVISOR ) . All other voltages of the 24 pin connector are ok. I can not get the IC or equivalent, can I just bridge 5v from anywhere on the board to this pin ( it is pin5 on ( the grey wire ) on the 24 pin connector. |
|
|
|
11-08-2021, 12:15 PM
|
#2 |
|
Badcaps Veteran
Join Date: Aug 2005
City & State: San Jose, CA
My Country: USA, Unsure of Planet
Line Voltage: 120VAC, 60Hz & 115VAC, 400Hz
I'm a: Professional Tech
Posts: 3,396
|
Re: Power supply build quality pictorial. part 2
Power Good (the grey wire) is a signal, not an output voltage. If all the output voltages from the power supply are in regulation, the Power Good should be logic high, 5V. If all output voltages are good but the Power Good signal is low, then the circuit that sources the power good signal (the "supervisor" circuit) is the problem. Wiring 5V to the Power Good signal pin could do more damage in the supervisor circuit, possibly affecting Over-Voltage, Over-Current, and Over-Temperature Protection functions.
__________________
PeteS in CA Power Supplies should be boring: No loud noises, no bright flashes, and no bad smells. **************************** To kill personal responsibility, initiative or success, punish it by taxing it. To encourage irresponsibility, improvidence, dependence and failure, reward it by subsidizing it. **************************** Anti-Covid-Vaxxer pig crap claim/prediction, Doctor: Heart Failure from mRNA Jabs "Will Kill Most People" | Principia Scientific Intl. ; Dr. Geert Vanden Bossche Warns COVID-19 Jab Injuries and Deaths Will Soon "Collapse Our Health System" (VIDEO) ; Fully Vaxxed May 2021; Since that time I've done 7 5Ks, 1 8K, 8 10Ks, and 4 half marathons |
|
|
|
|
11-08-2021, 12:17 PM
|
#3 |
|
New Member
Join Date: Jun 2021
City & State: Cairo Governorate
My Country: Egypt
I'm a: Knowledge Seeker
Posts: 16
|
Re: Power supply build quality pictorial. part 2
OK, Thank you
|
|
|
|
|
11-09-2021, 01:00 PM
|
#4 |
|
New Member
Join Date: Jun 2021
City & State: Cairo Governorate
My Country: Egypt
I'm a: Knowledge Seeker
Posts: 16
|
Re: Can I bridge power good signal in my PSU?
I managed to get wt751002 , are these equicvaleny 1. HY510N <=> WT7510 <=>*ST9S313*<=> PS113 <=>RT750
|
|
|
|
|
11-09-2021, 02:31 PM
|
#5 |
|
New Member
Join Date: Jun 2021
City & State: Cairo Governorate
My Country: Egypt
I'm a: Knowledge Seeker
Posts: 16
|
Re: Can I bridge power good signal in my PSU?
I managed to get WT751002 which is a power supervisory chip equivalent to ST9S313, but whhen I measured the IC input voltages there where no PGI , and all other voltages to the chip where ok , i guess that means that the problem is not with the chip. Right? what supplies the PGI to the chip? do you have schematics or any hint please? I work with GPUs this is my first time to work with PSU
 Or could it be a bad chip shorting the PGI input! your help would be appreciated. |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
