Telefunken D43F287N4CWII - Vestel 17MB110S - Recovery Firmware

[Tommes]

Hey Folks,

I'm searching for a Full Flash Recovery Software
for my Telefunken D43F287N4CWII

Mainboard Vestel 17MB110S
Panel: VES430UNDB-2D-N12
Productcode: 10119394

Does anyone know, where I can get it ?
Or is it possible, to extract it from a working mainboard ?

The Support Telefunken/Vestel GER couldn't help me.
The Vestel TR Support didn't answer my email.

History:
The main problem with my Telefunken D43F287N4CWII was,
it just goes out after a while, sometimes after a few minutes,
sometimes after a few hours.
Then I've swapped the mainboard for an identical model, all numbers
on the exchange board are identical. At first, the new mainboard
worked, but the colors weren't okay and neither the gamma values.
Apparently the panel data in the new mainboard doesn't match
my existing panel. Then, after a few "boot" processes, suddenly
the new mainboard no longer started, only the red LED flashes.
Then dismantled the old mainboard for a cross-check, it boots up
correctly. Presumably the new mainboard now has to be completely
reflashed with a recovery full flash software including the correctly
panel software file

Thk you vry much

[Tommes]

Oh, is there no recovery firmware available für the Vestel 110S ?

For the 110 and 110P i could find a '4-files-recovery' archive

[Diah]

Originally Posted by Tommes

Oh, is there no recovery firmware available für the Vestel 110S ?

For the 110 and 110P i could find a '4-files-recovery' archive

yours old one work.. so dump the eeprom of it ( round 2.5mb ) and flash it on the stop working one.. if my memory correct it should IC U81
cheap programmer CH341 can do the job.

[Tommes]

I did it some days ago, I cloned the SPI with CH341 & the Clip.
Writing worked well, but it didn't help, the board still didn't work.
I think, the TSOP48 Flash should be cloned/flashed, but I think
there is not Clip for TSOP48 to flash it.
I think. it must be unsoldered for flashing oder with some luck
with the recovery files and these files are my hope

[arizanotlari]

Hi.

Try these files ; https://disk.yandex.com.tr/d/1R-5fZtgh2fX6Q
https://disk.yandex.com.tr/d/d3fnc5ghGrbx3A

[Tommes]

Thank you very much for your files
I've tried to flash them.
The TV didn't flash the files

Press & hold OK -> Plug Power Cable in -> Power LED lights up 8x and USB Stick LED lights on too ...
Then the Power LED lights on permanently, the USB Stick LED light off
Not flashed

I think the mainboard is still not recoverable

(2 USB Sticks (FAT32), both USB Ports, both file archives tested)

[lotas]

Not all USB sticks will work, try old sticks up to 2Gb.

[Tommes]

The usb stick are 2GB and 8GB
I mean, i took one of them for core update on an other Vestel Telefunken TV
But I'll try it with another one

[Tommes]

Thank you very much for your help all.
It has worked now

The problem was, I swapped 2 Telefunken remote controls and
the OK button on the other remote did not appear to be the correct signal
It has flashed it, but the TV goes on briefly and then goes off again.
I just connected it to a damaged panel for testing,
I will test again on a healthy panel and see what it shows.
Maybe the board is lost for ever

[arizanotlari]

don't plug lvds cable. mb must be working without panel. if mb goes standby again firmware not fit to tv.

send me a pm for more firmware.

[the_thug]

Originally Posted by arizanotlari

don't plug lvds cable. mb must be working without panel. if mb goes standby again firmware not fit to tv.

send me a pm for more firmware.

Hello and sorry for the wrong topick, but i am trying to reach your website, and it shows error that it is unreachable. I have tried multiple devices and computers and even vpn but no good. Again i am very sorry, i know that this is not the place to ask, but i dot know where to find you.

[arizanotlari]

Hi, thanks for asking.

I closed site due to low traffic (daily 500 visitor).
Plus the selfishness of my colleagues began to piss me off.

Anyone can contact me here, electroda.pl and ****************

[the_thug]

Thank you ! I will know where to find you now.

[ducky29]

Originally Posted by arizanotlari

Hi, thanks for asking.

I closed site due to low traffic (daily 500 visitor).
Plus the selfishness of my colleagues began to piss me off.

Anyone can contact me here, electroda.pl and ****************

What about the old tips and links for firmwares that you had on the site? Is there any way we can get them back?

[arizanotlari]

Of course, I will continue to share the files, but I will keep the tips to myself for now

[ducky29]

Originally Posted by arizanotlari

Of course, I will continue to share the files, but I will keep the tips to myself for now

I don't know why I had a feeling that this day would come. Too bad I didnt download your website

[cheeky2]

Originally Posted by ducky29

I don't know why I had a feeling that this day would come. Too bad I didnt download your website

I must also say arizanotlari thank you for providing the files you have in the past it has been a great help in getting old TV's back to life and saving them from the landfill It is appreciated and I have learnt a lot from reading and browsing your website.
Take care Regards Anthony