![]() |
|
|
Thread Tools | Display Modes |
![]() |
#1 |
Badcaps Veteran
Join Date: Oct 2012
City & State: SG
My Country: SG
Line Voltage: 240v
I'm a: Knowledge Seeker
Posts: 309
|
![]() Hi folks, i have a sony home theater here thats with no power issue for a very long time, probably due to lightning strike. I have sorted out primary and fuse no longer blows out. This unit has 2 STR IC, one is STRF6168 and STRV153. Both has been replaced, electrolytic caps has been replaced, a few smd diodes replaced and resistors replaced. The problem now is, on VCC of STRV153, voltage are fluctuating between 12v to 15v up and down. Theres no voltages at all on any of the output pins. I have checked all the smd components, all seems to be reading accurately. But i know there IS something thats preventing the STRF6168 to start up. VCC on STRF6168 is 2v. Any kind souls that has repaired this unit before care to shed some light?
|
![]() |
![]() |
![]() |
#2 |
Badcaps Veteran
Join Date: Oct 2012
City & State: SG
My Country: SG
Line Voltage: 240v
I'm a: Knowledge Seeker
Posts: 309
|
![]() Is Sony schematic diagram parts stated in service manual is accurate? Just wondering. I noticed a diode on the board and the diode stated on the service manual is not same even though parts location number is same
![]() |
![]() |
![]() |
![]() |
#3 |
Badcaps Veteran
Join Date: Oct 2012
City & State: SG
My Country: SG
Line Voltage: 240v
I'm a: Knowledge Seeker
Posts: 309
|
![]() Anyone? Im going bonkers with this power supply
![]() Or i have changed the wrong zener diodes on D923 (10V), D924 (24V), D925 (5.1V) and D926 (10V)?? I followed the voltage rating according to service manual. I also noticed certain components thats on the service manual doesnt exist on the board, so i assume this board being used on several models. So i suspect the ZD could be wrong. Even after removing that diode, theres no signs of any voltages on the output. Last edited by DjKrish; 09-22-2021 at 01:14 AM.. |
![]() |
![]() |
![]() |
#4 |
Badcaps Veteran
Join Date: Oct 2012
City & State: SG
My Country: SG
Line Voltage: 240v
I'm a: Knowledge Seeker
Posts: 309
|
![]() Nobody?
|
![]() |
![]() |
![]() |
#5 | |
Badcaps Veteran
Join Date: Jun 2012
City & State: ☻
My Country: Canada
I'm a: Professional Tech
Posts: 8,161
|
![]() Quote:
Why did you replace the zener diodes? where they shorted? or did you just guess they were bad? Have you checked the caps such as C922, C924 Do you have any of the 4 secondary voltages on T902? If IC921 was bad, is R927 1Ω ok? Last edited by R_J; 09-23-2021 at 10:08 PM.. |
|
![]() |
![]() |
![]() |
#6 | |
Badcaps Veteran
Join Date: Oct 2012
City & State: SG
My Country: SG
Line Voltage: 240v
I'm a: Knowledge Seeker
Posts: 309
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#7 | |
Badcaps Veteran
Join Date: Oct 2012
City & State: SG
My Country: SG
Line Voltage: 240v
I'm a: Knowledge Seeker
Posts: 309
|
![]() Quote:
Last edited by DjKrish; 09-24-2021 at 02:09 AM.. |
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|