Asus X550LN screen glitches when flexing board

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ktmmotocross
    Boardkiller
    • Feb 2014
    • 3575
    • slovakia

    #1

    Asus X550LN screen glitches when flexing board

    Hello Have this Asus X550LN that have glitches on screen when flexing board and even turn off. I try to isolate flex point and it looks like it is bad ball under processor.

    Have this model discrette GPU run from start, or it first start on integrated GPU?
    I try to chceck if it is not bad ball under GPU as it is close to processor

Related Topics

Collapse

  • m1ch43lzm
    HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
    by m1ch43lzm
    Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
    Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
    05-12-2025, 08:37 PM
  • TheDando
    MSI GS66 Stealth 11ue-007us Board Number MS-16V41 VER.1 Screen Connector
    by TheDando
    Hey guys I've got a MSI GS66 Stealth 11ue-007us Board Number MS-16V41 VER.1 with a broken screen connector on the motherboard.I was wondering how I would go about finding a exact replacement for it.I can't seem to find any schematics that would help me so I'm kinda stumped.I did buy a screen connector that I thought was close enough but it doesn't really invoke much confidence in me that it works perfectly as plugging the screen into sometimes does output a "glitchy" image for just a few seconds.So now I'm kinda in a cross road where I'm pretty sure it could be a faulty screen but I...
    10-28-2024, 06:59 PM
  • DynaxSC
    ASUS STRIX Z490-F GAMING - No POST, stubborn board
    by DynaxSC
    Hi,

    I have this very stubborn ASUS mobo on the bench, and I already face the wall with it. It just refuses to POST, although everything seems to be OK.

    The situation looks like this:

    After connecting the board to the power supply on Nuvoton (SLP_S3#, pin 64), the Low signal (50 ohm resistance) appears immediately. PWRNTN# signal goes through Nuvoton to the chipset (confirmed after removing the chipset). The following conditions are then met for the chipset to generate the SLP_S3# signal:

    1. RTC oscillates normally (32.768KHz).
    ...
    07-08-2022, 05:45 AM
  • ShadowAi12
    ASUS ROG STRIX B550-F GAMING — Board not powering on properly
    by ShadowAi12
    Hi,
    I recently bought an ASUS ROG STRIX B550-F GAMING motherboard that was listed as "dead, not powering on." However, it does show some signs of life. I've performed several basic measurements and would like to share the results.
    • The board enters a "ready to power on" state after plugging in the PSU.
    • Pressing the power button increases power draw.
    • Sometimes, touching the RSMRST_L pad with a multimeter probe causes the board to shut off and return to standby.
    Measurements:
    (taken after pressing the power button, while the board is attempting to start)
    • H_SKTOOC#
    ...
    06-11-2025, 01:05 PM
  • howardc64
    A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
    by howardc64
    Problem

    This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
    08-04-2024, 10:36 PM
  • Loading...
  • No more items.
Working...