LCR T7 tester problem short

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • seifaldenn
    Member
    • Apr 2019
    • 40
    • Egebt
    #1

    LCR T7 tester problem short

    LCR T7 tester problem short( dz2---v05 )
    you changed v05 working now Not a fixed measurement
    Any measurement out 2.95v
    Kim can solve the problem out 2.95v
    Attached Files
    Tags: None
    • seifaldenn
      Member
      • Apr 2019
      • 40
      • Egebt
      #2
      Re: LCR T7 tester problem short

      I need help repairing

        Comment

        • seifaldenn
          Member
          • Apr 2019
          • 40
          • Egebt
          #3
          Re: LCR T7 tester problem short

          How can the problem be solved
          Attached Files

            Comment

            • seifaldenn
              Member
              • Apr 2019
              • 40
              • Egebt
              #4
              Re: LCR T7 tester problem short

              I need software atmega324

                Comment

                • harp
                  Badcaps Veteran
                  • Jun 2022
                  • 598
                  • Planet Earth
                  #5
                  Re: LCR T7 tester problem short

                  Maybe here
                  https://disk.yandex.com/d/yW8xa5NJgUo5z

                    Comment

                    • seifaldenn
                      Member
                      • Apr 2019
                      • 40
                      • Egebt
                      #6
                      Re: LCR T7 tester problem short

                      Originally posted by harp
                      Maybe here
                      https://disk.yandex.com/d/yW8xa5NJgUo5z
                      ga324 is not available

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • Crystaleyes
                          LCR T7 tester problem
                          by Crystaleyes
                          Hi all.

                          Several months ago, whilst testing a box of old used caps which I had 'assumed' were discharged, the T7 LCR tester I was using was damaged.
                          When the button was pressed, the display would briefly light up and then go dead.

                          So, I stuck the T7 in the freezer for ten minutes and 'Bingo!' it came back to life.

                          Only thing was that after it 'defrosted' at room temperature, the problem returned.

                          After freeze spraying components one at a time, I managed to pin the problem down to a SOT-8 chip. An STC 15L104W. Which until now, I had...
                          11-02-2022, 03:11 PM
                        • Tarot Superstars
                          Short Circuit tester
                          by Tarot Superstars
                          Hello.
                          I have seen a short circuit tester made with 3 * 9V batteries, a voltage limiter component and a resistor connected to the probes of a multimeter.
                          The theory is that the meter becomes sensitive enough to read very low resistances and the lowest resistance to ground on a circuit is likely to be a short circuit in that area.

                          Link
                          The Amazing $1 Short Finder Upgraded! Convert ... - YouTube
                          https://www.youtube.com/watch?v=0eixDdCpiO4

                          My multimeter isn't normally sensitive to very small resistance, but when I put a 1 mega ohm resistor...
                          09-25-2023, 09:11 AM
                        • DynaxSC
                          Extreme High Current & Low Voltage Short Killer ??
                          by DynaxSC
                          Hi Folks

                          I'm looking for a extreme high current short killer solution for a reasonable cost.

                          I have an LGA1700 motherboard (ASUS PRIME Z790-P WiFi) where I exchanged the LGA socket already 3 times, and every time after the socket exchange I get a short of power supply lines VCORE (V variable) and VCCIN_AUX (1.8V).
                          After taking off the socket, the shorts dissappear again.
                          The soldermask on the socket is already partially demaged from the heat, so I have reconstructed the soldermask by manually painting the missing soldermask parts with a very small top of a...
                          10-15-2024, 10:13 AM
                        • theone111
                          Problem with LG Plasma 60PM6700 - Random power downs
                          by theone111
                          I have an LG Plasma TV 60PM6700 for the past ~12 years.

                          In the last ~3-4 months I have been having some issues.
                          1. Problem: It started with random picture disappearing (sound still worked).
                            Frequency: Happened about once a week.
                            Solution: Had to turn off TV wait a few seconds before turning it on again.
                          2. Problem: Then it got worse and the TV started to shut down and when turning on the no picture just sound.
                            Frequency: Happened about once a week.
                            Solution: Had to turn off TV wait about 10-20 seconds and turn it on again to solve.
                          3. Problem: TV shuts down
                          ...
                          1 Photo
                          07-22-2024, 10:36 AM
                        • Stephen
                          MacBook Pro 14" A2442 Short on PPBUS_AON but no short present when injecting voltage!
                          by Stephen
                          I check PPBUS_AON and there is a short present on the line, the computer shows a short when testing for short to ground, so when I inject voltage into the line, I get 0AMPS so no short is showing up. I have replaced a blown cap on this board that exploded and tested for the short and it is now removed. Any suggestions? I tested voltage at the line when the fuses are connected and I am getting 1.2 Volts at the line.
                          02-06-2025, 12:03 PM
                        • Loading...
                        • No more items.
                        Working...