Panasonic TX-48CX400B low LED volts

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sintv
    Member
    • Feb 2015
    • 37
    • scotland

    #21
    Re: Panasonic TX-48CX400B low LED volts

    This seems to be a common problem with no solution. Ive got the same problem and I checked all leds and theyre fine. Just have to wait till I get a working set in so I can swap boards.

    Comment

    • zwarder
      Member
      • Oct 2013
      • 45
      • United Kingdom

      #22
      Re: Panasonic TX-48CX400B low LED volts

      Same problem here IC heating up to 110 degrees C then cuts out

      Comment

      • jesseharris227
        New Member
        • Dec 2020
        • 1
        • uk

        #23
        Re: Panasonic TX-48CX400B low LED volts

        Originally posted by Duranitron
        its not normal for the mp3394s to heat up if you have the schematics try to check all components surrounding the ic. also check the OVP circuit if you have an led backlight tester with current display let it fire up all the LED backlight from 80volts to 120vdc and let it lit for about 30min to an hour to isolate the problem that the LED backlight is not the culprit. my experience is 80vdc to 120 vdc current read out of 300mA max. it can pump up to 48 watts thats ok. there is always a possibility of shorting led when it reach the normal voltage so this test will surely catch it.check also if it has mosfet connected to the IC. hope you fix it just try and don't over see the obvious.
        Do you have schematics or know where I can get them fit this board

        Comment

        • PanasTC
          New Member
          • Nov 2023
          • 4
          • Canada

          #24
          I have similar issue where boars states 400V and I am measuring 160.

          Comment

          Related Topics

          Collapse

          • Andre Gilbert
            Panasonic TC-P55ST50 8 blinks then no blinks
            by Andre Gilbert
            Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
            Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.

            TV Model: Panasonic TC-P55ST50
            ...
            11-20-2024, 08:52 PM
          • MisterAIL
            PS5 digital / No Power / No Beep / Good power supply
            by MisterAIL
            Hi everyone,

            Brought a non functionnal PS5. Apparently only a bad PSU...
            No beep, nothing.

            After some tests i found this :
            - PSU is fine (12 volts stable)
            - 12 volts line is shorted
            - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
            - By the way, nothing change. No signal, no power, no beep.

            Mesuring all rails with my workbench psu (12 volts input)
            - 0.00 amp drawing
            - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
            03-12-2024, 03:24 PM
          • AquaMan Ua
            Problem with PANASONIC CF53 laptop after changing BIOS settings
            by AquaMan Ua
            Hello. I am asking you for a hint on how to solve the problem with my touchbook Panasonic CF53-2 standart model. After setting up the BIOS, the laptop displays the wrong image until Windows loads. (More precisely, it displays, but distorted, instead of the Panasonic image immediately after turning it on, it displays what is in photo #1 in the attached file) Then the image appears when Windows starts loading and then there are no problems with the screen until the reboot. If you enter the BIOS, just a black screen. If you connect an external screen, the image on it is the same as on the built-in...
            05-17-2025, 09:40 AM
          • BTubbs200
            Dead Dell Latitude 5420 not receiving 20 volts from USB-C charger
            by BTubbs200
            Hello,

            Dell Latitude 5420 P137G
            Board: LA-K491P REV A01

            I have received this laptop which was described as "does not power on or accept charge." Battery shows no sign of charging when charger is plugged in, nor does the board show any signs of life when battery is unplugged and charger is plugged in. No light from the LED at all or any other indications of activity.

            Board seems to have no shorts, all power rails are fine and show high resistance.

            When charger is plugged in, voltage is present in 3.3V rail but absent in others....
            01-24-2025, 08:15 PM
          • sam_sam_sam
            MPJA 10 AMP @ 0 to 30 Volts Switching Power Supply Cap Fault
            by sam_sam_sam
            I have this 10 amp 0 to 30 volt switching power supply that decided to have a 630 milliamperes draw on it at 0 volts

            I open it up to find non brands name capacitors in it

            I am not sure how this switching power supply is set up

            Could someone please explain how this power supply works

            Here is the capacitor ESR results

            (1) 47uf@50 volts 0.46
            (2) 47uf@50 volts 0.45
            New 47uf@50 volts 0.35

            (1) 100uf@25 volts 0.34
            (2) 100uf@25 volts 0.35
            New 120uf@50 volts 0.08

            (1) 220@25 volts 0.13...
            10-21-2018, 10:02 AM
          • Loading...
          • No more items.
          Working...