hi have installed a motherboard Intel desktop DH67CF which I think unused but pc does not start tried first with power supply (corsair tx 650) then with an another (ACE model: 500T) thought it was wrong with the first one but same result what could be wrong ?
Announcement
Collapse
No announcement yet.
Trying to renew my old computer
Collapse
X
-
Re: Trying to renew my old computer
Sounds like a bad board.... Tried reseating things? Verified CPU, RAM, and GPU are good?<--- Badcaps.net Founder
Badcaps.net Services:
Motherboard Repair Services
----------------------------------------------
Badcaps.net Forum Members Folding Team
http://folding.stanford.edu/
Team : 49813
Join in!!
Team Stats
Comment
-
Re: Trying to renew my old computer
Is it powering up, but nothing else happens other than fans and LEDs? That is a common issue. The first thing to try, is to reseat the video card and the RAM.
A dead CPU can be the cause of the above-mentioned symptom.
Especially on socket 775 and later-era systems, it can mean poor contact with the RAM. They're known for not always bleeping and sometimes will do nothing, except for powering up, just like a dead CPU.Last edited by RJARRRPCGP; 01-28-2022, 12:20 PM.ASRock B550 PG Velocita
Ryzen 9 "Vermeer" 5900X
16 GB AData XPG Spectrix D41
Sapphire Nitro+ Radeon RX 6750 XT
eVGA Supernova G3 750W
Western Digital Black SN850 1TB NVMe SSD
Alienware AW3423DWF OLED
"¡Me encanta "Me Encanta o Enlistarlo con Hilary Farr!" -Mí mismo
"There's nothing more unattractive than a chick smoking a cigarette" -Topcat
"Today's lesson in pissivity comes in the form of a ziplock baggie full of GPU extension brackets & hardware that for the last ~3 years have been on my bench, always in my way, getting moved around constantly....and yesterday I found myself in need of them....and the bastards are now nowhere to be found! Motherfracker!!" -Topcat
"did I see a chair fly? I think I did! Time for popcorn!" -ratdude747
Comment
-
Re: Trying to renew my old computer
We need more details here.
I see the board is socket 1155 with H67 chipset. Manual says it supports only 65 Watt TDP CPUs (i3, i5, and i7). The board also has on-board video and a PCI-E 16x 2.0 slot.
With that said, first and foremost, does the board even power up? In other words, if you press the power button, do the system fans come On and stay On? The PSU fan may not come On if it's a newer PSU and has an "Eco" mode feature or just doesn't run the fan until it gets hot. However, the CPU fan should spin and keep spinning for as long as the system is up and running. If the system seems to only power up and turn off, you may have a power issue. If you do, stop here and let us know. If not, then continue with the below items.
1) What CPU are you using?
2) What about RAM - what kind of RAM are you using? Can you provide a picture or specs written on the RAM?
3) Have you tried resetting CMOS yet? If not, disconnect power from motherboard and remove CMOS battery for a few minutes. Then re-insert battery and re-connect to PSU. See page 54 and 54 in the manual and check your BIOS jumper block configuration is correct - it should be in the "Normal" position when the board is operating properly. But to reset CMOS, put the jumper in the "Configure" position and try turning On the motherboard with that. If board does turn On in the Configure position, move jumper to Normal position, set up things in CMOS, save, and restart. Board should boot normally.
4) Which graphics port are you using on the motherboard - on-board or external graphics card? If on-board, try an external (discrete) video card.
5) Does the board have a mini speaker/buzzer? (According to the manual, page 13, there should be one - it's labeled "N" on the diagram.) If not, try connecting one to hear if BIOS throws up any errors. If none, remove all the RAM modules and see if the board beeps then. Report back what you get here.
6) If none of the above work, disconnect power from motherboard and remove CPU from socket. Check CPU socket pins carefully under good light and see if any are bent or broken.
Comment
-
Re: Trying to renew my old computer
Hi momaka and thanks for all the advice.1) mothercard lights up whith the power cord ,presses on start no fan, power supply is ok tried with jumper and it works. Bios jumper is on normal Cpu: i3 and it has no pins but I will check the socket tomorrow. Have connected the speaker but no sound and have used onboard graphic card HDMI port. I have not tried your suggestions because it is quite late 04 but I will return with pictures and answers to your questions thank you very much
Comment
-
Re: Trying to renew my old computer
Intel stopped making motherboards a long time ago. I don't think the quality was up to snuff next to other brandsCap Datasheet Depot: http://www.paullinebarger.net/DS/
^If you have datasheets not listed PM me
Comment
-
Re: Trying to renew my old computer
Hi Stj as you said so the battery was dead encapsulated one. I have examined the psu socket's pin momaka asked me to do the upper half is straight and the lower half looks to be curved but the whole lower half so I think they should be so you can maybe see in the picture
Comment
-
Re: Trying to renew my old computer
CPU socket looks good to me.
Originally posted by stj View Postmake sure the battery is good - stupid as that sounds.
there are a few boards that wont boot without it!!<--- Badcaps.net Founder
Badcaps.net Services:
Motherboard Repair Services
----------------------------------------------
Badcaps.net Forum Members Folding Team
http://folding.stanford.edu/
Team : 49813
Join in!!
Team Stats
Comment
-
Re: Trying to renew my old computer
Originally posted by bohaboha View Postto everyone who helped, I put it all together but it does not work exactly the same as before. I wonder if I force the start using a bridge on the power supply instead of the start button it does not damage the motherboard?
maybe the bios is corrupt and needs to be reprogrammed.
Comment
-
Re: Trying to renew my old computer
I have started led lights, fan working but nothing on screen also no usb that responds the black ones I do not have the other usb yet, no sound either, do not know what to do next. .
You wrote about corrupt Bios that may need to be reprogrammed how to do it ?
Comment
Comment