Badcaps.net Forum
Go Back   Badcaps Forums > Troubleshooting Hardware & Devices and Electronics Theory > Troubleshooting Power Supplies and Power Supply Design
Register FAQ Calendar Search Today's Posts Mark Forums Read

 
Thread Tools Display Modes
Old 11-27-2021, 01:57 PM   #1
hugonoizz
New Member
 
Join Date: Nov 2021
City & State: Torino
My Country: Italy
I'm a: Knowledge Seeker
Posts: 3
Default Sony ADP-200ER Ps4 Power Supply

Hello

I am new to this forum and kind of new to board repair as general, I have learned how to change stuff using soldering iron and hot air but I am still lacking good troubleshooting skills, so this brought me here…

I have a ps4 bought from ebay with the intention to repair (probably has already been to numerous technician before me), it has been dropped at some point so it has broken plastic everywhere…

I’m any case it has a well known fault, when you press the power it starts but after less then 0.5 seconds it power itself off.

So I took the power supply apart to check the condition and to my surprise I saw it was already taken apart before because you can see fresh solder near the first fuse and also I think near the pfc choke (I think is that)

Anyway this is what I checked:

- 4volt rail OK
- Fuses Ok
- No short (for the best of my knowledge)
- Shorting the sense pin -> 12v coming up for about 0.1 seconds but slowly decrease and then no 4v
- Every time I start the 12v rail I have to remove the power to try again

I watched some guy’s video on YouTube about how this power supply works and It was very illuminating so I thought maybe it’s the pfc choke (the guys reference it with that name) so I took it out and found that it has broken plastic and it shows a short (see attachments)
I would like to find a replacement for that anyway
It’s like a big coil of wire right?
Also the main capacitor is around 130uf, can that be the problem?


I already order another power supply from china but I would like to repair this one just to learn
Ps sorry any verbal or vocabulary error, I am Italian, English is tricky to me
hugonoizz is offline   Reply With Quote
Old 11-27-2021, 02:40 PM   #2
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 26,668
Default Re: Sony ADP-200ER Ps4 Power Supply

the unductor (pfc choke)
is just a coil, it's supposed to look like a short.
put it in your component tester and check the inductance.
stj is offline   Reply With Quote
Old 11-27-2021, 03:21 PM   #3
hugonoizz
New Member
 
Join Date: Nov 2021
City & State: Torino
My Country: Italy
I'm a: Knowledge Seeker
Posts: 3
Default Re: Sony ADP-200ER Ps4 Power Supply

Quote:
Originally Posted by stj View Post
the unductor (pfc choke)
is just a coil, it's supposed to look like a short.
put it in your component tester and check the inductance.
Not sure if I put it correctly
If I giggle it around I read 0.25 mH same resistance
Attached Images
File Type: jpg C32ECD12-8F60-43DF-BF31-DA2D6370C5C0.jpg (278.3 KB, 14 views)
hugonoizz is offline   Reply With Quote
Old 11-27-2021, 05:19 PM   #4
stj
Great Sage 齊天大聖
 
stj's Avatar
 
Join Date: Dec 2009
City & State: Europe
My Country: some shithole run by Israeli agents
I'm a: Professional Tech
Posts: 26,668
Default Re: Sony ADP-200ER Ps4 Power Supply

i dont know what it should read, but i expect to see a much higher reading!
stj is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



Badcaps.net Technical Forums © 2003 - 2022
Powered by vBulletin ®
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
All times are GMT -6. The time now is 04:48 PM.
Did you find this forum helpful?