JVC TV Model LT-65N675- No picture

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • angelos
    Badcaps Veteran
    • Dec 2012
    • 562
    • South Africa

    #1

    JVC TV Model LT-65N675- No picture

    Hi guys,
    This set has no image. The back lights are running but the TCON seems dead.
    The fuse on board is ok, 12V is present. The problem seems as if there are voltages missing but due to weird markings I cannot see VGH clearly. Anyway, I disconnected both ribbons feeding the panel to see if my voltages come up but they don't. Up to know I was looking to purchase a complete used tcon board but they are not available.
    Can anyone who knows these sets guide me so that i can diagnose the fault. I believe it to be the DC to DC buck converter.
    I have a image not to good quality but now that I know that i need to repair it i will remove it and zoom into its design.
    I think JVC might be similar to your RCA products

    Any help would be greatly appreciated.
    Attached Files
  • angelos
    Badcaps Veteran
    • Dec 2012
    • 562
    • South Africa

    #2
    Re: JVC TV Model LT-65N675- No picture

    The chip RT6931 below has 5 solder spots marked CPOUT, UH, UL, LH and LL and there is 0V on all 5 when set is running.
    Is the UH actually VGH???
    Check photo
    Attached Files

    Comment

    • angelos
      Badcaps Veteran
      • Dec 2012
      • 562
      • South Africa

      #3
      Re: JVC TV Model LT-65N675- No picture

      Any help anybody?

      Comment

      • angelos
        Badcaps Veteran
        • Dec 2012
        • 562
        • South Africa

        #4
        Re: JVC TV Model LT-65N675- No picture

        I measured some voltage points and these are the results

        VONE = 0V
        STV2 = 0V
        VIN_1.2V = 1.23V
        VL = 0V
        UL = 0V
        LL = 0V
        VH = 0V

        The pico fuse has 12V on both sides
        The big chip in the centre reaches 50 degree celsius in 2 minutes.
        All these voltages were taken with both panel ribbons disconnected.
        I measured resistances on all SMD caps and could not find any shorted ones.
        This board is unavailable and on the web i find this board but it is for a Sony TV. I doubt the software will be the same and thus i will not order it.

        I guess this tv is going to the landfill.

        Comment

        • angelos
          Badcaps Veteran
          • Dec 2012
          • 562
          • South Africa

          #5
          Re: JVC TV Model LT-65N675- No picture

          What a dead forum!!!

          Comment

          • yokoono
            Badcaps Veteran
            • Apr 2010
            • 476

            #6
            Re: JVC TV Model LT-65N675- No picture

            "VIN_1.2V = 1.23V"
            VIN is the supply voltage of the t-con and must be 12V. The fuse is blown or the motherboard does not power the t-con. If the safety is burned, you have an excessive consumption on t-con.

            Comment

            • R_J
              Badcaps Legend
              • Jun 2012
              • 9529
              • Canada

              #7
              Re: JVC TV Model LT-65N675- No picture

              There is a solder spot labeled HVIN3_12V (next to ICB1?) do you have +12 volts there?

              Comment

              • angelos
                Badcaps Veteran
                • Dec 2012
                • 562
                • South Africa

                #8
                Re: JVC TV Model LT-65N675- No picture

                Originally posted by R_J
                There is a solder spot labeled HVIN3_12V (next to ICB1?) do you have +12 volts there?
                Hi, yes i will check that on saturday and get back to you
                Regards

                Comment

                • angelos
                  Badcaps Veteran
                  • Dec 2012
                  • 562
                  • South Africa

                  #9
                  Re: JVC TV Model LT-65N675- No picture

                  Originally posted by yokoono
                  "VIN_1.2V = 1.23V"
                  VIN is the supply voltage of the t-con and must be 12V. The fuse is blown or the motherboard does not power the t-con. If the safety is burned, you have an excessive consumption on t-con.
                  Hi there,
                  I don't understand your reasoning. The label says 1.2V and i am getting 1.23V so that is spot on.

                  Comment

                  • yokoono
                    Badcaps Veteran
                    • Apr 2010
                    • 476

                    #10
                    Re: JVC TV Model LT-65N675- No picture

                    VIN is the supply voltage and is 12V not 1.2V. Measure at both ends of the fuse (F1) and see if you have 12v.

                    Comment

                    • diif
                      Badcaps Legend
                      • Feb 2014
                      • 6978
                      • England

                      #11
                      Re: JVC TV Model LT-65N675- No picture

                      Originally posted by angelos
                      Hi there,
                      I don't understand your reasoning. The label says 1.2V and i am getting 1.23V so that is spot on.
                      Perhaps inspect that marking with some magnification. It's a via not a.

                      Comment

                      • angelos
                        Badcaps Veteran
                        • Dec 2012
                        • 562
                        • South Africa

                        #12
                        Re: JVC TV Model LT-65N675- No picture

                        Ok, I will take a proper photo of it and also test it tomorrow when I am back in office.
                        Thanks so far.

                        Comment

                        • angelos
                          Badcaps Veteran
                          • Dec 2012
                          • 562
                          • South Africa

                          #13
                          Re: JVC TV Model LT-65N675- No picture

                          Hi Guys, i did further tracing around the voltages that are missing on the TCON and i noted the following. When mains power is applied to the tv the TCONs ribbon supply voltage from the main board is a steady 12V if the set is on standby or ON. This tells me that something else must switch on the 12V when picture is required. I have made some marking on the photo i sent you to explain properly.
                          ICA1 i assume is either a mosfet or a dc to dc converter, i dont know. What i do know is that when i removed the ICA1 i saw that 4 circuit tracks are common as the 12V input and one is on the output called HVIN_12V. The last pin is a bias pin or enable pin and is driven directly from the RT6931GQW IC.
                          I was monitoring the HVIN_12V pin when applyuing main power and it shot up to about 3.3V and dropped to zero. It never came up again.
                          If i measure ohms from HVIN_12V to ground i get 38.5 k ohms so there is no short there.
                          So here is my conclusion either RT6931GQW is faulty or goes into protection or who knows maybe there is no data from the main being detected by this chip so it does not start up???
                          The TV lies open awaiting your help.
                          Thanks so far.

                          Comment

                          • angelos
                            Badcaps Veteran
                            • Dec 2012
                            • 562
                            • South Africa

                            #14
                            Re: JVC TV Model LT-65N675- No picture

                            here is the picture!
                            Attached Files

                            Comment

                            • yokoono
                              Badcaps Veteran
                              • Apr 2010
                              • 476

                              #15
                              Re: JVC TV Model LT-65N675- No picture

                              Problems where it is surrounded by red?
                              Attached Files

                              Comment

                              • angelos
                                Badcaps Veteran
                                • Dec 2012
                                • 562
                                • South Africa

                                #16
                                Re: JVC TV Model LT-65N675- No picture

                                Thanks Yokoono,
                                I saw those coils.. The plastic tops have cracked or perished. Probably from heat. So you agree with me the RT6931 chip might be the problem? So I will order it and hopefully it fixes the issue.

                                Comment

                                • diif
                                  Badcaps Legend
                                  • Feb 2014
                                  • 6978
                                  • England

                                  #17
                                  Re: JVC TV Model LT-65N675- No picture

                                  The IC next to the damaged coils also looks damaged as does the component above it.

                                  Comment

                                  • R_J
                                    Badcaps Legend
                                    • Jun 2012
                                    • 9529
                                    • Canada

                                    #18
                                    Re: JVC TV Model LT-65N675- No picture

                                    Those coils are not plastic but powdered iron (or similar) The side of the ic looks damaged as well, this is not from heat but from something striking that part of the board.

                                    Comment

                                    • angelos
                                      Badcaps Veteran
                                      • Dec 2012
                                      • 562
                                      • South Africa

                                      #19
                                      Re: JVC TV Model LT-65N675- No picture

                                      I will replace that chip and see what happens! Will take months for the part to arrive.

                                      Comment

                                      • angelos
                                        Badcaps Veteran
                                        • Dec 2012
                                        • 562
                                        • South Africa

                                        #20
                                        Re: JVC TV Model LT-65N675- No picture

                                        Or maybe order a complete board via Ebay and hope it works.
                                        Just a question, if the board arrives and I fit it and there is something wrong like the picture is flipped upside down or some other issue. I remember somebody telling me that there is a program loaded into the tcon. If so then would it be fair in saying that i could unsolder the old eprom and solder it into the new one and it could then work?
                                        I think the eprom could be part "ICE11" or is it loaded into the big square chip in the centre?

                                        Comment

                                        Related Topics

                                        Collapse

                                        • TR103
                                          Samsung TV model UE50TU: rebooting, backlight, sound, but no picture
                                          by TR103
                                          Hi, I have a Samsung UE50TU with:
                                          - sound and backlight, but no picture
                                          - when it arrived, it had a picture for a few seconds
                                          - it keeps rebooting
                                          - without ribbon cable between the two panel boards, it does not reboot but I have no picture
                                          - without cable between mainboard and lcd panel, it does not reboot (but obviously i have no picture)
                                          - when i try a tape fix, its keeps rebooting, unless I tape off pin 1 (the innermost pin). In that case it does not reboot but I have no picture.

                                          - without cable between mainboard and lcd panel and with a jumpered...
                                          01-22-2025, 04:12 PM
                                        • Fripacks
                                          No picture LG model 50PT350
                                          by Fripacks
                                          Hi guys,
                                          I have problems no picture with LG model 50PT350, first of all, I change the 2 buffer boards who was no good, the TV working 2 weeks and today same problem, I check and I found Zsus board defect now, I change it for a new one and no picture, I check VS VA and 5 volts , all this voltage are there, I disconnect the upper buffer board, no picture, I disconnect the lower buffer board, no picture, what I have to check now?...
                                          05-19-2023, 12:06 PM
                                        • Document Archive
                                          HP ProBook 640 G1 Base Model Notebook 600 Specification for Upgrade or Repair
                                          by Document Archive
                                          This specification for the HP ProBook 640 G1 Base Model Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 640 G1 Base Model boardview and 640 G1 Base Model schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet,...
                                          09-06-2024, 05:27 AM
                                        • Document Archive
                                          HP ZBook 14 G2 Base Model Notebook 14 Specification for Upgrade or Repair
                                          by Document Archive
                                          This specification for the HP ZBook 14 G2 Base Model Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 14 G2 Base Model boardview and 14 G2 Base Model schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or...
                                          09-06-2024, 05:27 AM
                                        • Document Archive
                                          HP EliteBook 840 G2 Base Model Notebook 800 Specification for Upgrade or Repair
                                          by Document Archive
                                          This specification for the HP EliteBook 840 G2 Base Model Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 840 G2 Base Model boardview and 840 G2 Base Model schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet,...
                                          09-06-2024, 05:27 AM
                                        • Loading...
                                        • No more items.
                                        Working...