Pls tell me Generally what this is, and if you KNOW a substitute, what is that. Thanks, see pic, as I can read is C007?
Attached Files
-
-
Re: Help Identifying component, what is this?
Can you provide more information? IE: is one leg connected to ground? (regulator) or is voltage fed into one pin and out another (mosfet) Is there a board designator U, IC, Q, D etc. it seems to have a white arrow which might designate pin1
Two pins (2,3) appear to be connected to heavy traces and pin1 seems to be a thin trace indicating it could be for a gate or base connection. Does that thin trace running under the part connect to pin1? or are pins 1&2 connected together?Last edited by R_J; 10-04-2019, 02:47 PM. -
Re: Help Identifying component, what is this?
Looks like a diode to me since only two pins are connected and the traces are somewhat thick.
What kind of board is this? laptop?
EDIT: I just saw the thin trace going to the bottom pin. Most likely some FET or Transistor.Last edited by KvnTM; 10-04-2019, 02:46 PM.Comment
-
Re: Help Identifying component, what is this?
The blown part is directly under the LDVS1 video connectors, on the bottom of this Dell 2330 AIO Motherboard. None of the three pins go to ground. The thin trace went to pin 3 in my pic. Pins 1 and 2 are eventually connected through other elements and tracing. The tweezers point where the C 007 was. I have failed to find that part number on any component in the Russian 1200 page manual. Ideas? Let's take a guess......I got nothing to lose that's not already goneAttached FilesComment
-
-
Re: Help Identifying component, what is this?
This computer's video screen went bezerk, and this must be the reason. Add pic, after removal.Attached FilesLast edited by captainKKK; 10-04-2019, 03:42 PM.Comment
-
-
Re: Help Identifying component, what is this?
Add better pic?
No board designatorsAttached FilesLast edited by captainKKK; 10-04-2019, 03:47 PM.Comment
-
-
Re: Help Identifying component, what is this?
My guess would be that it is a switch (mosfet) maybe to switch the panel/t-con voltage on and off if it is connected to the lvds cable. There is likely a supply voltage on either pin 1 or 2 and the control pin would be pin 3Last edited by R_J; 10-04-2019, 03:54 PM.Comment
-
Re: Help Identifying component, what is this?
Yes, connected to lvds. RJ, can you suggest a common part number in that kind of package?Last edited by captainKKK; 10-04-2019, 03:52 PM.Comment
-
Re: Help Identifying component, what is this?
Do you have a schematic/manual for this board? Just putting an unknown fet there isn't a good idea. It could also be the backlight pwm signal line or backlight power rail. There is a reason why it blew up.
Please measure the resistance on all pads of the device to GND.
Just replacing it won't help. it will blow again.Comment
-
Re: Help Identifying component, what is this?
.Last edited by captainKKK; 10-07-2019, 07:53 PM.Comment
-
I need help identifying this IC and, if possible, the value of the capacitors next to it. It is part of the HDMI circuit of an EVGA RTX 2060 GPU. It suffered a short circuit, leaving the graphics card without video and the TV without image....06-06-2025, 07:48 PM -
Subject: Help Identifying IC on 820-02020 (MacBook Pro A2338 M1, 2020) — C02045500 / EKQ8LL1A
Hi all,
I'm working on a MacBook Pro A2338 M1 (2020) with logic board 820-02020.
The machine has a power issue — not powering on, and I'm trying to trace the fault.
While inspecting the board, I found a cluster of components
This area looks damaged or burned — there are about 4–5 components that seem affected
I've attached a close-up photo of the chip and its surrounding area (see... -
Hi everyone
I have a 70mai Dash Cam A510 which failed after about 3 months of being installed in my car, likely due to heat, i got it from aliexpress so no point in trying to return it for warranty (and shipping it back would cost me almost the same as a new one from ali)
The camera would boot loop showing 70mai logo on the screen, sometimes it would boot fine then the live view would freeze or display purple lines
I already took it apart, and found out that the camera boots fine if i unplug the camera module from the main PCB, sometimes "playing" with the connector... -
I am having trouble identifying this chip, it's near where the power comes into the board. From a HP Victus 15. Says RW=AL UG1 -
Hi, i need help identifying component on HP x360 440 G1 motherboard ( Rumble 17869-1)...
Comment