3d printed electronics bench accessories and equipment

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Urshurak776
    New Member
    • Jul 2021
    • 6
    • United States

    #21
    Re: 3d printed electronics bench accessories and equipment

    As the OP stated, I printed several items from thingiverse for small parts storage (resistors, diodes, etc.) They work great.

    Comment

    Related Topics

    Collapse

    • BOSCHNJAK
      by BOSCHNJAK
      ABOUT ME INTRODUCTION FILE

      2
      024 BEV, BIH, SARAJEVO START PROJECT: ELECTRIC VEHICLE TOYOTA 4 RUNNER CONVERSION http://www.bev.ba/TOYOTA4RUNNER/index.html

      2023 BEV, BIH, SARAJEVO START PROJECT: SECRETS AND MANUFACTURING PLANS (AS MY REPLICA) OF THE LIBERTY ENGINE 2.0.
      2022 BEV, PROJECT ?
      2021 BEV, PROJECT ?
      2020 BEV,BiH, Sarajevo: PROJECT IS: HOW TO SWITCH OFF PERMANENT MAGNET FIELD and HOW TO SWITCH ON PERMANENT MAGNET FIELD?
      2019 BEV, Croatia, Ston:, Broce: PROJECT - PROJEKT ELEKTRIČNI GLISER http://www.bev.ba/ELEKTRICNIVANBRODSKIMOTOR/indexHR.htm...
      12-28-2023, 02:09 PM
    • Hypersapien
      Artist seeking to tinker with electronics safely
      by Hypersapien
      Howdy folks! I'm an artist in the video game industry, and my job entails making a lot of mechanical and sci fi assets. I thought it might be a good practice to start disassembling some electronics to be more familiar with how real electronics are manufactured and assembled, which is how i found my way to these forums.

      When I started researching what tools I might need, I quickly encountered the warning "Some devices can maintain a potentially lethal charge in their capacitors, even up to years after last being powered on", which was enough of a scary thought for me to...
      10-22-2023, 01:31 PM
    • sumilumi
      700mv ripple on Akai Sampler linear supply
      by sumilumi
      Hi fellow troubleshooters. This is my first post on badcaps. I've recently setup an electronics workbench. i'm also building a studio with old equipment bought faulty at low cost.
      I've been into electronics since the mid 80's and particularly in the last few years though only getting hands on with repairs now. My knowledge gaps are significant so I'll be posting here to seek guidance advice and general practical applied learning.

      On my bench today is an old ca. 1993-95 Akai hardware sampler. This runs on both a linear and Smps supply. Both are getting on in age and ripple...
      01-02-2022, 10:12 AM
    • Eniaro
      Bench test a series X
      by Eniaro
      How do you bench test a series X? I was planning to find a defective PSU to use its connector, but before I go about doing this, I was wondering if there's any bench PSU to the series X connector adapter available
      06-17-2025, 01:46 PM
    • proton32064
      General Question- Electronics from 70's and 80's
      by proton32064
      I have a question since I am new here and I don't know if this is the right forum to ask these questions or if I am wasting your time.
      I am 67 and have a lot of Radios and Electronics I grew up with which puts a lot of them at 50 years or older.
      A lot of the capacitors are obviously bad but this is my problem.
      An example would be the Panasonic RC-7469 Clock Radio and the Panasonic RF-888 Radio.
      I have others like a Canon L-162 Nixie Desktop Calculator 110AC, etc.

      I have the Service Manuals to some of these and other electronics I have and grew up with and...
      05-09-2025, 05:16 PM
    • Loading...
    • No more items.
    Working...