Announcement

Collapse
No announcement yet.

Picking caps for Antec SU-380

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Picking caps for Antec SU-380

    In my search for a proper 5v heavy ATX power supply, I selected an old Antec SU-380 that I've had in storage for a long time. Opening the power supply reveals a couple bulged capacitors. I removed all the caps and made a map for myself. I found the datasheet for the PCE TUR series in this thread:
    https://www.badcaps.net/forum/showthread.php?t=14159
    It says these are general purpose, so I assume I can replace them with any general purpose capacitors, but I don't really know anything about power supply circuits or reading capacitor datasheets. Despite this, I've been shopping for replacements:

    Low voltage side
    EC502 PCE TUR 3900uf 16v 105c 13x33 https://www.digikey.com/en/products/...2-5X30/6050005
    EC504 PCE TUR 2200uf 10v 105c 10x25 https://www.digikey.com/en/products/...10X23/15667956
    EC602 PCE TUR 2200uf 6.3v 105c 10x20 https://www.digikey.com/en/products/...10X20/15667812
    EC503 OST RLS 3300uf 10v 105c 13x25
    EC601 OST RLS 3300uf 6.3v 105c 13x20 https://www.mouser.com/ProductDetail...ZE6R3ELL332MK2
    EC400 OST RLS 1000uf 16v 105c 10x16 https://www.mouser.com/ProductDetail...ZE160ELL102MJ2
    EC402 OST RLS 220uf 16v 105c 6x11
    EC201 OST RLS 220uf 16v 105c 6x11
    EC200 OST RLS 2200uf 10v 105c 10x20 https://www.mouser.com/ProductDetail...ZE100E222MK20S

    High voltage side
    EC300 Hitachi HU4 220uf 400vdc 105c 30x30
    EC100 OST RLS 22uf 50v 105c 5x11 https://www.mouser.com/ProductDetail/232-50ZL22MEFC5X11
    EC101 OST RLS 47uf 25v 105c 5x11 https://www.mouser.com/ProductDetail/232-25ZL47MEFC5X11
    EC302 OST RLS 68uf 25v 105c 5x11
    EC303 OST RLS 4.7uf 50v 105c 5x11

    Fan board
    C1 OST RMH 22uf 35v 105c 5x7

    I've been following recommendations in this thread for replacing the OST RLS series:
    https://www.badcaps.net/forum/showthread.php?t=14433
    Some of the series mentioned there have had a limited selection or availability in regards to size and capacitance.

    I've linked the caps I've picked out so far, but I'm wondering if somebody with more knowledge can give me some advice on what to buy.

    #2
    Re: Picking caps for Antec SU-380

    When it comes to power supplies, one of the most important things to consider is the ripple current. Look at the datasheets, make sure the ripple current matches or is bigger than the cap you're replacing it with (but not crazy too high). There is another factor called ESR but it usually does not apply to PSU's. The caps for them are sometimes listed as for power supplies.

    I did this for an antec basiq 380 some years ago it worked great

    I have pictures somewhere. Also usually if you don't see the mains (400v) bulging you usually don't need to replace it
    Cap Datasheet Depot: http://www.paullinebarger.net/DS/
    ^If you have datasheets not listed PM me

    Comment


      #3
      Re: Picking caps for Antec SU-380

      Thanks for the advice. I ended up ordering mostly Panasonic FR-A series to replace the OST RLS, and I ordered both general purpose and low ESR equivalents for the few general purpose PCE TUR caps. Is there any reason I shouldn't replace those with low ESR caps?

      Comment


        #4
        Re: Picking caps for Antec SU-380

        i only use low-esr caps.
        for small ones i use whatever is cheapest - usually FR's
        large caps i'v used FC and FK in the past.

        Comment


          #5
          Re: Picking caps for Antec SU-380

          I wasn't able to find a low-ESR cap for the primary, but I did buy a Nichicon LGU cap (LGU2G221MELB). I'm not sure it's a good replacement for the Hitachi HU4 that was in there already though, so I could just put that one back. I'm going to attach the datasheets here if anyone can give me an idea.
          Attached Files

          Comment


            #6
            Re: Picking caps for Antec SU-380

            the high voltage caps you want to try to get 105' temp rated with a long lifespan

            Comment


              #7
              Re: Picking caps for Antec SU-380

              The Nichicon LGU should be just fine as a replacement for the Hitachi prinary capacitors.

              Comment


                #8
                Re: Picking caps for Antec SU-380

                Originally posted by ajdrenter View Post
                I wasn't able to find a low-ESR cap for the primary, but I did buy a Nichicon LGU cap (LGU2G221MELB). I'm not sure it's a good replacement
                ripple current :
                1,13A your Hitachi
                1,1A Nichicon LGU

                Comment

                Working...
                X