[ROM] Abir X6 vacuum robot

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • lietuvis10
    Member
    • Aug 2019
    • 16
    • Lithuania
    #1

    [ROM] Abir X6 vacuum robot

    Hello, I would like to share Abir x6 vacuum robot cleaner rom files that I extracted from SPI ROM chips. One chip is on main board and another is on camera module (the problem with robot was in camera rom, after re-write with other robot's rom it started working perfectly fine).

    Maybe this will help you, because I couldn't find it anywhere.

    Camera Dump: 4MB
    MB Dump: 2MB
    Attached Files
    Tags: None
    • ljgonzalo
      New Member
      • Jul 2022
      • 1
      • Argentina
      #2
      Re: [ROM] Abir X6 vacuum robot

      Hi lietuvis, what was your problem with de Vacuum robot?

        Comment

        Previous template Next

        Related Topics

        Collapse
        • ex250
          SDJ01RM vacuum robot not powers on, all dead
          by ex250
          Hi friends, I have this vacuum robot at home that is not starting any more, no leds working, power button doing nothing, battery reading seems ok arround 14.4v, I suspect that mainboard is faulty, seems that there is not any clear brand model on it, and of course could not find any schematic. The trand of the vacuum is the Roidmi SDJ01RM, on some sites appears as vacuum mop Eve plus 60 or similar

          If any one could point for where to start... would appreciate, new board is quite expensive arround 100 USD or more

          Many thanks and Merry Christmas to all...
          12-24-2022, 05:12 AM
        • flat-earther
          Hoover FM216LI cordless vacuum refuses to charge
          by flat-earther
          I have a Hoover FM216LI cordless vacuum which isn't charging its internal battery.

          I opened up the unit, and it has 6x Samsung ICR18650-22P cells connected in series.
          5 cells were at about 3.3-3.1V. one was at 2.4V, so I assumed this cell was bad that's why the vacuum wasn't charging so I replaced it with another 18650, but after that the problem still persists, the vacuum turns on a bit and then cuts out since the batteries are empty.

          So I think the over discharged battery wasn't the culprit, it was a symptom of the unit not being able to charge its batteries....
          06-06-2025, 03:14 AM
        • Awesomerp
          Sencor SVC7020BK robot vacuum cleaner problem
          by Awesomerp
          Hello I have been trying to identify and fix a problem with a robot vacuum cleaner, which when switched on cleans for like 3-4 seconds and stops, all the driving, sweeping and vaccum motors stop.
          On the pcb from a battery connector up to a main microcontroller everything seems to be fine (vcc pin input is 5v constant when a switch is switched on).
          And the switch itself is fine looking at the quality of my soldering
          Red LED keeps blinking during those 3-4 working seconds, and when the robot stops LED just remains lit.
          The green one for some reason does not even...
          09-23-2022, 11:36 AM
        • Habble7
          I need a BIOS dump for the Samsung S49CG934SU monitor
          by Habble7
          The Samsung S49CG934SU monitor does not power on - no LED indicator activity and no response to power button. However, when 21V power is connected, it immediately draws 0.8A of current with no display output. The motherboard processor gets warm, and there is continuous reading activity from the W25Q128BV BIOS chip.

          Suspected Cause:
          I suspect the BIOS may have been corrupted during a power interruption while updating the firmware. The official website provides firmware updates, but they can only be installed via USB flash drive.

          Troubleshooting Attempts:
          ...
          05-22-2025, 07:28 AM
        • Mephysis
          DUMP DVR HIKVISION DS-7208HGHI-K1 (80389 Rev 1.3 Firmware)
          by Mephysis
          Hello guys i really need help, i recently updated my DS-7208HGHI-K1 and it somehow got bricked, I've got it up and working now by flashing a new dump file i found but the serial number is really wrong and the uploader of the dump file probably intentionally did it.

          I still have the bricked dump file is it possible to transfer the serial number of the "bricked dump" to the "working dump"?
          03-27-2025, 02:34 AM
        • Loading...
        • No more items.
        Working...