Vintage Pace desolder station PPS-100 pump motor bad

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • shelby5041
    Badcaps Legend
    • Feb 2009
    • 1504
    • united states of america usa
    #1

    Vintage Pace desolder station PPS-100 pump motor bad

    hi

    i jsut got this pace PPS-100 desolder solder station vintage for free

    the motor does not turn when powered on..it just makes some rumbling sounds thats it

    no replacements avail for reasonable price..

    is this fixable or maybe an alternate motor

    here is a pic of stock photo i found online
    Tags: None
    • shelby5041
      Badcaps Legend
      • Feb 2009
      • 1504
      • united states of america usa
      #2
      Re: Vintage Pace desolder station PPS-100 pump motor bad

      nevermind i fixed the issue..motors works good now
      Attached Files

        Comment

        • redwire
          Badcaps Legend
          • Dec 2010
          • 3902
          • Canada
          #3
          Re: Vintage Pace desolder station PPS-100 pump motor bad

          tell us what you found and fixed lol. The motor capacitor might be low value.

            Comment

            • shelby5041
              Badcaps Legend
              • Feb 2009
              • 1504
              • united states of america usa
              #4
              Re: Vintage Pace desolder station PPS-100 pump motor bad

              Sure..there is a plate on back of motor where vsc is...with a thin shim.metal gasket ..i took plate off pkate and motor turned fine by hand so i put plate and shim metal gasket back on ...it then worked...apparently it was bound up against the plate...from years of idled...my neighbor gave me it...its very interesting...even has a rotary tool..)
              Last edited by shelby5041; 04-16-2020, 01:54 PM.

                Comment

                • llonen
                  Badcaps Veteran
                  • Sep 2014
                  • 495
                  • hampshire
                  #5
                  Re: Vintage Pace desolder station PPS-100 pump motor bad

                  I was looking for a replacement pump for the MBT 250, well more specifically the diaphragm overhaul kit, then unable to source that my thoughts turned to a replacement pump / motor assy and found prices for second hand units were not meeting with my approval. In the end was able to source a complete replacement controller at a very cheap price that did meet with my approval lol.

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • sam_sam_sam
                      ZD-915 vacuum pump motor mount service alert
                      by sam_sam_sam
                      If you have this Desoldering Gun Station there is something you should be aware of the two screws that hold the motor to mounting for pump can come loose and make raddling noise

                      One note this unit has been repaired already once because of switching power supply regulator ic chip failure
                      Now this with the vacuum motor mounting issue yes I give this Desoldering station a very hard work out and use about every weekend to do some type of project

                      The fix is taking the vacuum pump assembly out and take the metal cover off and you will see the two screws on it
                      ...
                      09-19-2021, 02:15 AM
                    • juergenb
                      Nescafe Aeroccino, still fails with new Motor (red flashes only once)
                      by juergenb
                      Hi,

                      i am asking for some Help.
                      I have one of these Nescafe Aeroccino (Milk Frother) things with a bad motor.
                      The Motor didn´t start anymore and internet is full of users just swapping the motor for a Mabuchi RF-500TB-12560.
                      So i got a few of these from Banggood.

                      I swapped the motor and now i have a new fault condition.

                      In a working Frother you would press the start button, it will light red and work for a few minutes.
                      If you press longer it will light blue and just mixup the milk.

                      With the new Motor it just starts...
                      03-23-2021, 11:24 AM
                    • sbt123
                      charnwood w821 mini wood lathe motor problem
                      by sbt123
                      hi there,im having a look at repairing a wood lathe for my dad,(charnwood w821)the problem is when turning up the variable speed control,the motor starts to stop and start by itself,if i continue to turn up the speed it will trip the mcb in the consumer unit,there is also a slight smell of burning from the speed controll box.,Another strange symptom is the lathe can be unplugged from the mains after switching it off and the motor will spin a couple of times by itself,so far ive put a new speed controll potentiometer on and new motor brushes,ive also tested the motor windings and everything looks...
                      10-27-2024, 03:43 AM
                    • mikey5791
                      Help identify this motor
                      by mikey5791
                      Hi all forum members,
                      Found this unknown motor discarded in a junk yard and took home for learning experience. By the look of it, I suspect it is taken out from a type of air blower probably running on ac power. I used digital multimeter on ohm/resistance scale and it doesn't read anything on those 2 black wires. So, this motor is not shorted and should be good to run.

                      Correct me if i am wrong on the initial test.
                      Can anyone kindly advice on how to test run this motor based on visible external two black wires. Fyi, i don't see any marking on the motor body nor smell anything...
                      11-24-2023, 07:54 PM
                    • sam_sam_sam
                      1970 Metal Lathe Control Circuit blowing fuses on the 120 volt section failing meager test below 60 mega ohms
                      by sam_sam_sam
                      I was working on this machine yesterday and I now going to use an incandescent lights instead of a fuses to figure out what the issue is with it blowing control voltage rail but this not the only issue the coolant pump failed the meager test as well as the main motor as well this motor has 12 motor wire leads instead of the normal 9 wires

                      This metal lathe has a weird motor setup it has a soft start motor with a “Y” and a delta type of motor winding setup and it is not done in the motor pucker head enclosure it is with four different contactors wired in a configuration I have not...
                      12-29-2024, 07:18 AM
                    • Loading...
                    • No more items.
                    Working...