Un43nu7100

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Plurxtc1
    Senior Member
    • Oct 2014
    • 131
    • USA

    #1

    Un43nu7100

    Anyone having issues with the edgelit where it burns on one side? I replaced both left and right side with brand new edgelit and the same left side burned out again. It only lasted one day. I don't want to replace it again with a chance of it burning.
    Attached Files
  • brucetv
    Badcaps Veteran
    • May 2015
    • 281
    • united states

    #2
    Re: Un43nu7100

    Yes, we are refusing to do any edge lit back light repairs on Samsung Tv's due to premature failure and what we find when we get in there. The clear diffuser many times get's melted because they are sitting right on top of the led's which will leave light leak where it's melted. Or they can get so hot it can crack the diffuser and you will see the crack behind the panel. If you own a edge lit Samsung make sure it's not set on Dynamic in picture settings and bring the backlights down to 50% or lower. These Tv's were designed to fail and I wouldn't bother spending any money putting in a new set of bar's. This is why they are going to a new backlighting design. Samsung you suck.
    Attached Files

    Comment

    Related Topics

    Collapse

    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • Stephen
      A2442 MacBook Pro 14" Two Left SIDE USB C ports charge but no data
      by Stephen
      Right SIDE usb.c port charges and transfers data without issue, two left side uSB c ports charge but do not receive or see data. Was liquid damaged, and repaired significantly and thought we were in the clear but appears this is the last issue that is rearing its head. I am trying to locate the RETIMER chip that communicates the DATA TX/RX but I cannot seem to find it on the schematic or maybe I am just so tired my eyes wore out lol. Any help would be great.
      05-29-2025, 10:35 AM
    • Gjackson
      SMEG induction cooker error EA on both left hand side cooktops
      by Gjackson
      Hi all,

      I have a SMEG cooktop with a EGO 72.08041.002 power board. The two left hand side cooktops started to slowly fail, sometimes stopping with an EA error (Power board failure according to the manual) after a couple minutes boiling some water and eventually they completely failed and now get an EA error on both of them at all times. Visual inspection of the board went over ok, I checked the IGBT's and rectifiers and they seem fine, what should I look at next as this is the first time I'm fixing an induction cooker, I'm suspecting capacitors in this case, Which ones should I look...
      07-09-2024, 01:46 PM
    • frannyjunk
      Vizio M60-C3 left side of screen + a couple other areas dim
      by frannyjunk
      My Vizio M60-C3 was dead. No power, no lights. Just nothing. So I took the back cover off and noticed 4 bulging caps on the power supply board, so I replaced them (green low esr capacitors in the picture). The tv now works! But there are some areas that look dim (see picture). In particular, the left side has a dim band. I know that the led strips run horizontal, yet this band is vertical. Could it be that the led driver board is bad? Could the blown caps have taken out the led driver board? Or is this just a coincidence that every left side led on each strip just went out?...
      11-10-2021, 08:09 PM
    • V3dran
      Diffuser/LPG for UE50NU7022KXXH
      by V3dran
      Hello,
      I'm trying to repair a UE50NU7022KXXH with a cracked diffuser/lpg and now also with burned leds
      There are 4/5 white spots on the bottom that are not visible since the left side is dark now so I want to change the diffuser/lpg

      Looking the samsung spare parts, I see that there is a DIFFUSER PLATE and a LPG so I'm wondering what is really broken?
      https://www.samsungparts.eu/samsung-...n61-15659a.htm DIFFUSER PLATE 1125x625x2,5mm
      https://www.samsungparts.eu/samsung-...n61-15661a.htm LPG 1101x619x2,7mm...
      06-26-2025, 01:54 AM
    • Loading...
    • No more items.
    Working...