Announcement

Collapse
No announcement yet.

Adapting a samsung panel to Vestel 17MB211

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Adapting a samsung panel to Vestel 17MB211

    Hi, I have a telefunken tv with a broken panel (VES315WNDA-2d-n12). The tv has a 17mb211 board.
    Since I had a samsung with a good panel (df320agh-r1) I try to adapt this to the telefunken.

    Pinout was almost the same (the only thing I have to move the connect on the 17mb211 according to the image below ... from double lvds to wxga fcc).



    Panel is working bad badly. Color is wrong ... image was flip (I was able to correct this playing with ptf.ptf file ... b8HFlip = 1 b8VFlip = 1 to be precise ).

    Does any of you have any experience with vestel board and ptf.ptf file parameters?

    I attach also the ptf.ptf file ..
    Attached Files

    #2
    Re: Adapting a samsung panel to Vestel 17MB211



    Last edited by saronno; 04-23-2022, 02:11 PM.

    Comment


      #3
      Re: Adapting a samsung panel to Vestel 17MB211

      Samsung HD Panel file : https://disk.yandex.com.tr/d/672hb9tqJMwcZw
      https://www.badcaps.net

      Comment


        #4
        Re: Adapting a samsung panel to Vestel 17MB211

        I didn't spot any difference but flip parameters. Am I right?

        to me, looking at the image, it seems as if there aer not the full range of colors, like when you setting pc video card to 8 bit or 16.
        Last edited by saronno; 04-23-2022, 03:20 PM.

        Comment


          #5
          Re: Adapting a samsung panel to Vestel 17MB211

          T-CON intgertated at Panel ?? if yes can you show here the T-CON chip so i can see it to check yours parameter

          Comment


            #6
            Re: Adapting a samsung panel to Vestel 17MB211

            actually this problem looks like a lvds socket problem. I tried the panel software on the Samsung panel and it worked without any problems.
            https://www.badcaps.net

            Comment


              #7
              Re: Adapting a samsung panel to Vestel 17MB211

              VES315WNDA-2d-n12 = CN16
              Samsung HD = CN15

              CN14 should not be used this chassis
              https://www.badcaps.net

              Comment


                #8
                Re: Adapting a samsung panel to Vestel 17MB211

                Originally posted by Diah View Post
                T-CON intgertated at Panel ?? if yes can you show here the T-CON chip so i can see it to check yours parameter
                Tomorrow I will open it again to make some photos.

                Comment


                  #9
                  Re: Adapting a samsung panel to Vestel 17MB211

                  Originally posted by arizanotlari View Post
                  VES315WNDA-2d-n12 = CN16
                  Samsung HD = CN15

                  CN14 should not be used this chassis
                  Probably you are right. I move the connector a couple of week ago so I am not sure ... anyway right now it's at cn15

                  Comment


                    #10
                    Re: Adapting a samsung panel to Vestel 17MB211

                    Originally posted by arizanotlari View Post
                    actually this problem looks like a lvds socket problem. I tried the panel software on the Samsung panel and it worked without any problems.
                    You mean I should recheck cable and connectors?

                    If so, I guess it could be some problem with the tx pins

                    clock is improbable since I have a picture .... but one of the tx line could impair some specific bit in the frame if it's not working or malfunctioning.
                    Last edited by saronno; 04-23-2022, 04:25 PM.

                    Comment


                      #11
                      Re: Adapting a samsung panel to Vestel 17MB211

                      I didn't find the datasheet for the samsung panel I am trying to adapt to the vestel, but I find this one below I suspect have the same pinout


                      https://datasheetspdf.com/pdf-file/9...g/LTA320AN01/1

                      This is a picture of the connector of my panel


                      So, as I said, it has the same pinout of the board (CN15) but it was mirrored.

                      Comment


                        #12
                        Re: Adapting a samsung panel to Vestel 17MB211

                        We need picture of chassis.
                        https://www.badcaps.net

                        Comment


                          #13
                          Re: Adapting a samsung panel to Vestel 17MB211

                          Ok, I solved. It was the connector.
                          First thing I asked to myselft "why everything is reddish" ... so in the samsung pdf
                          i posted above I checked "what if red is stuck" ... and so tx0 has to be 1 all the time .... and so I checked with my multimeter and the two line were shorted together (a little bridge under the connector not visible from above). Anyway I changed the connector completely (the old one was in bad condition after a couple of soldering/desoldering) and now everything if fine.

                          Anyway, Thanks for the help.

                          Comment


                            #14
                            Re: Adapting a samsung panel to Vestel 17MB211

                            Just to sum it up if everybody else want to try to adapt a samsung panel to this
                            vestel board: yes, it's possibile but be careful with the pinout since it's mirrored.

                            Comment

                            Working...
                            X