Yamaha HTR-5630RDS AMP sitting down

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • roadrash
    Badcaps Veteran
    • Oct 2015
    • 490
    • U.K.

    #1

    Yamaha HTR-5630RDS AMP sitting down

    I wonder if anyone has any idea what could be causing this to shut down. When you turn it on you hear the relay click and it all lights up. Then about 4-5 seconds later the relay clicks again and it turns off. I have looked carefully at it and checked all connections and it all seems ok.
    Anyone have a suggestion?
    Attached Files
  • stj
    Great Sage 齊天大聖
    • Dec 2009
    • 30977
    • Albion

    #2
    Re: Yamaha HTR-5630RDS AMP sitting down

    that type of construction is just begging for cracked solder joints!

    Comment

    Related Topics

    Collapse

    • jm1234
      9V relay temperature 40C
      by jm1234
      Hi, I'm seeing one 9V relay having temperature 40C on its 9V (primary) side. Does that seem right? I switched 2 relays on that board and the temperature was the same (on the same position), so I'm sure it's not a faulty relay. I measured voltage on that relay and it was 9.5V DC, so that looks good. I don't see any other relay on that board having that kind of temperature and they have 9V on them too.
      I thought maybe the transistor that is switching this relay keeps switching on/off, so I also checked for AC and there was almost none: 0.3V using mV range. No steady frequency was shown, but...
      05-09-2024, 03:03 AM
    • edugimeno
      Biomass Boiler not driving cleaner motor relay. ENERTRES BIOMASA BI-650
      by edugimeno
      Hi everyone!
      I have this board that suddenly stopped supplying power to an output that drives an interchanger cleaner motor.
      I checked while the board was in place with all wires attached and there's no AC voltage on the corresponding plug X5
      This X5 is driven by fuse F8 (tested OK) which comes from the second orange relay
      To make sure there are no charcoaled contacts inside the relay, I got a 24VDC power supply and got it ready to manually power up the coil side of these relays.
      I respected the polarity, positive to cathode of protecting diode
      So provided all...
      04-18-2024, 01:15 PM
    • sam_sam_sam
      Mitsubishi CNC switching power supply board dead / relay board bad diode failure
      by sam_sam_sam
      I was working on this CNC machine today found no keyboard functioning no control relay powering on
      The screen powered on and was giving an operation error but the manual was not very clear about what the error exactly was but with a little bit of troubleshooting and finding out that the control relays not powering on and no keyboard functions we narrowed down to this one switching power supply which of course does not have any indicator LED light they are on the keyboard interface/relay controller board

      Found shorted diodes on main controller relays there are 3 of them that...
      01-07-2023, 05:43 PM
    • sanalelevenstar
      Yamaha RX-V485 Wn9711 Update
      by sanalelevenstar
      Help Needed: Yamaha RX-V485 Network Issue After Firmware Update (WN9711 Error)

      Hi everyone,

      I'm facing an issue with my Yamaha RX-V485 receiver. During a firmware update, the process failed, and now the USB, Bluetooth, and network functionalities are not working. Occasionally, the receiver displays the error code WN9711.

      I came across Yamaha Technical Bulletin No. 0103, which describes a similar issue for models like the RX-V4A, RX-V6A, and RX-A2A. According to the bulletin, the issue can be resolved by shorting soldering points (e.g., J260 for RX-V4A or...
      12-04-2024, 04:32 AM
    • AlexVG
      YAMAHA CLP-550 without of sound
      by AlexVG
      Hi.
      I have an old YAMAHA CLP-550 without sound. (Some times I can get some kind of noise or distorted sound)
      I have replaced all green marked elements, but it gave me nothing.
      The IC12 chip LC9116A-105 (red marked) remains under suspicion yet.

      But it is custom YAMAHA's chip, and I can't find any information about it.
      Maybe somebody came across with the same issue?
      Any information will be very useful. I will be very appreciated.
      Thank you....
      06-08-2025, 09:29 AM
    • Loading...
    • No more items.
    Working...