![]() |
|
|
Thread Tools | Display Modes |
![]() |
#1 |
Member
Join Date: Jun 2016
City & State: UK
My Country: UK
I'm a: Professional Tech
Posts: 42
|
![]() This picture is of a Canon EOS M50 camera logic board which isn't powering on.
It gets 5v from the micro USB charger but no voltage after the diode or any nearby components. The battery connector is the 3 pins on the right edge of the board and also has 0v on all pins Am I correct in thinking that if there is 0v on the 3 pins at the bottom of the diode then there is a problem with the diode? If I were to replace the diode, would anyone know how to identify it for me? Last edited by SMDFlea; 03-02-2021 at 09:17 AM.. Reason: Added model to thread title |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Dec 2013
City & State: Littleborough
My Country: england
I'm a: Professional Tech
Posts: 180
|
![]() Well,firstly ,I would be almost absolutely certain it isn't a diode.
|
![]() |
![]() |
![]() |
#3 |
Member
Join Date: Feb 2013
City & State: Edina, mn
My Country: Usa
I'm a: Knowledge Seeker
Posts: 49
|
![]() I believe that is a diode.
I believe the R050 DZ8N is a fuse. That is most likely the problem. What is it reading resistance wise? Plug in the numbers and do some digging. I have repaired a number of Canon and Nikon DSLRs with a single bad fuse in the power circuit. |
![]() |
![]() |
![]() |
#4 |
Member
Join Date: Jun 2016
City & State: UK
My Country: UK
I'm a: Professional Tech
Posts: 42
|
![]() Thanks Kg74. R050 DZ8N reads 3.7 ohms
|
![]() |
![]() |
![]() |
#5 |
Member
Join Date: Feb 2013
City & State: Edina, mn
My Country: Usa
I'm a: Knowledge Seeker
Posts: 49
|
![]() https://html.alldatasheet.com/html-p...4/1/EMD62.html
Does this help? You should post some better pictures, including the front and back of the board. I have searched for sometime on the RO50 DZ8N - appears to come up as a resistor - maybe the DZ8N is some further specifications. If so then it should be .05 ohms. |
![]() |
![]() |
![]() |
#6 |
Super Moderator
Join Date: Jan 2018
City & State: York
My Country: UK
I'm a: Knowledge Seeker
Posts: 6,501
|
![]() Its a TOKO marking code i think, with that wide band.
|
![]() |
![]() |
![]() |
#7 |
Member
Join Date: Feb 2013
City & State: Edina, mn
My Country: Usa
I'm a: Knowledge Seeker
Posts: 49
|
![]() Man I am not happy. I spent an hour working on my message and was timed out.
Summary - I think it is a regulator of some type. I think there are three pins, one in the middle from the trace going down. Does the camera charge through the camera or does it have a separate charger? What is the problem with the camera? What happens when you supply power to the battery connector direct? I think you would be best served moving this to the power supply forum if the circuit is for charging which is what it looks like. The 5V in has to be brought down to about 3.7 to charge the battery. |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|