[HELP] Lenovo V15-IIL "partial dead"

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • todenkopf
    Member
    • Oct 2014
    • 49
    • UA

    #21
    Re: [HELP] Lenovo V15-IIL "partial dead"

    Originally posted by phantomEVO
    so game over?
    If you decide to remove any pwm ic, you should also remove mosfets that are controlled by that ic prior to applying power. Unconnected gates of that mosfets will sporadically open, and let input voltage run into output line.

    However, your IC has only integrated mosfets, which was removed along with IC as well. So seems its not that case i've mentioned above. Try to replace PU9700.
    Last edited by todenkopf; 07-02-2022, 01:28 PM.

    Comment

    • mcplslg123
      Badcaps Legend
      • Jun 2015
      • 7262
      • india

      #22
      Re: [HELP] Lenovo V15-IIL "partial dead"

      Originally posted by phantomEVO
      so game over?
      Not over. Though i mentioned it in post#3 that PU9700 is a multi regulator with builtin mosfet+dc -dc circuit but in a hurry overlooked it. Since removing PU9700 means removing all the connected fets also, chances of damage is very unlikely. So you can proceed with further diagnosis.

      Comment

      • Sephir0th
        Badcaps Legend
        • Oct 2020
        • 1262
        • Germany

        #23
        Re: [HELP] Lenovo V15-IIL "partial dead"

        Low Ohms readings on 3.3V ALW load side is almost always a dead PCH though.
        FairRepair on YouTube

        Comment

        • phantomEVO
          Badcaps Veteran
          • Mar 2013
          • 487
          • USA

          #24
          Re: [HELP] Lenovo V15-IIL "partial dead"

          i don't know how to go ahead. now 3,3valw is totaly shorted....but nothing getting hot...

          Comment

          • mcplslg123
            Badcaps Legend
            • Jun 2015
            • 7262
            • india

            #25
            Re: [HELP] Lenovo V15-IIL "partial dead"

            Exact resistance on 3VALW rail?? Is the measurement without the ic soldered??

            Comment

            • Xmaxsi
              New Member
              • Dec 2018
              • 2
              • Argentina

              #26
              Re: [HELP] Lenovo V15-IIL "partial dead"

              i have exactly the same issue, only that when i connect the my power supply to the charging port it reads 0.009 amps, it charges the battery but only turn power lights on without power supply, only battery power, but nothing getting hot. it's the weirdest problem i encounter so far in a laptop

              Comment

              • mon2
                Badcaps Legend
                • Dec 2019
                • 13880
                • Canada

                #27
                Re: [HELP] Lenovo V15-IIL "partial dead"

                Check the voltage to ground of each pin on mosfet PQ101. Post each measurement.

                Connect the power adapter.

                Comment

                • mcplslg123
                  Badcaps Legend
                  • Jun 2015
                  • 7262
                  • india

                  #28
                  Re: [HELP] Lenovo V15-IIL "partial dead"

                  Since laptop is charging, i dont see any issues in PQ101. You mean to say when power button is pressed,power on indicator glows but no voltage on coils? If so what is the exact consumption after pressing power Button?

                  Comment

                  • RethoricalCheese
                    Badcaps Legend
                    • Mar 2013
                    • 1517
                    • Estonia

                    #29
                    Re: [HELP] Lenovo V15-IIL "partial dead"

                    Probably not related to issue on hand but I just want to make a note that this board has a common fault

                    Bad solder under CPU, which causes removable RAM not to work. Works with soldered RAM only.

                    Comment

                    Related Topics

                    Collapse

                    Working...