http://www.myce.com/news/apple-repla...gn-flaw-78600/
I've read about the power delivery capabilities of USB Type-C: a maximum of 100W (20V @ 5A).
I've read about the power delivery capabilities of USB Type-C: a maximum of 100W (20V @ 5A).
-
My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics. -
Re: Oh no! USB Type-C cable problems
Danger! Poor quality USB Type-C cables can damage or destroy your devices (or even cause a fire)!
http://www.zdnet.com/article/poor-qu...-your-gadgets/
A list of cables tested by APC Magazine: http://tinyurl.com/apc427-usb
If Amazon can do that
, so can eBay!
http://www.valuewalk.com/2016/03/ama...cable-sellers/
http://androidcommunity.com/amazon-n...ters-20160331/My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.
-
Problem
This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached.... -
I have a broken connector (believe it's a 6 pin mini-DIN) on a cable. The metal shroud and all but one of the pins are separated from the cable, and just stuck together for the photo. The other end is an unknown rectangular connector. The cable is for the foot pedals on an Italian made electronic piano, and the company is out of business. Looking for ideas on how to fix it. I have a soldering iron, but I'm not very skilled at soldering, so getting a retrofit for the broken end may be beyond my ability. The other end would be easier to replace, if I could get a mini-DIN cable with the same number...
-
Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.
The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.
Original T-con:
Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.
First replacement T-con:
I thought it might be t-con and ordered new t-con from china(supposedly tested)... -
Hello,
on this laptop hp g72 b52sf i have screen problems as you can see with the photo joined in attachments.
the used graphic card is "intel hd graphics" and the id of the integrated screen is : "monitor/SEC3354".
i verified the driver of the péripherals and they are ok. i verified the definition and settings of the graphic card and of the screen : definition 1600x900 and refreshment frequency :60hz. (they are the sames for the graphic card and the screen).
i don't understand the reasons of the white stripe at the bottom of the screen below the task... -
The Lenovo laptops V15 and V17-IIL with I5 or i7 CPU and probably many other Lenovo laptop from this time with 10th or 11th generation Intel CPU suffer from a design flaw regarding the display/camera/microphone connector on the motherboard which is badly placed and the cheapest of the cheap connectors imaginable. As the cable is too near to the display and the connector does not fix it proper in place the cable develops little defects and those over time lead to a plethora of possible quirks or failures starting from the named RAM problem or sudden switching off in special when the display is...
Comment