a1297 820-2914A - 18v at Vcore!!

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • marce002
    Badcaps Veteran
    • May 2018
    • 316
    • Argentine
    #1

    a1297 820-2914A - 18v at Vcore!!

    Hello

    An easy one, but just in case i ask> It is a no power mac, but saddly come with a missing mosfet Q7035 , tested vcore coils and AC volt is present at them, so 18v in the coils!! (I' ve never seen this) is this a garbage? no green led just 4mah consumption....
    no water damage looks pristine

    thanks in advance
    Last edited by marce002; 09-25-2021, 06:24 PM.
    Marcelo J
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • barry101
      Apple 820-3662 VCore shorted to ground.
      by barry101
      Hi, Would appreciate some help.
      I have an Apple Late 2013 15" A1398 MacBook Pro with Logic Board 820-3662.
      Get charger light but no fan spin or chime. No liquid damage.
      Found PPBUS and VCORE both shorted to ground. Other rails were ok.
      Removed VCORE MOSFETS U7310, U7320 and U7330. Found U7330 was in fact shorted.
      With the 3 MOSFETS removed, get PPBUS and fan spin. VCORE is still hard shorted to ground (0 ohms).
      Attempted voltage insertion on VCORE to locate short using bench supply set at 1.0 VDC and 4.95 Amps (max current for my...
      06-24-2025, 07:34 AM
    • Salvador Pérez
      Help identifying the function of these two coils - MSI Delta 15 (MS-15CK1)
      by Salvador Pérez
      Hello everyone, I'm troubleshooting an MSI Delta 15 (MS-15CK1) motherboard, and I need help identifying the function of the two coils marked in the attached image. The laptop powers on and responds to the keyboard, but the screen does not turn on-neither the LCD nor the backlight. I've checked the main power rails, and all other coils seem to have the expected voltages:

      • 0.91V for the GPU
      • 1.7V for VRAM
      • 3.3V and 5V rails 1.8V for the BIOS
      • 0.9V for the CPU and iGPU 1.2V for the RAM

      However, these two coils are not showing any voltage....
      1 Photo
      03-10-2025, 11:50 AM
    • mikzs
      Rx580 8gb sapphire nitro+ turn off vcore randomly
      by mikzs
      Hello, this is my first post, English is not my native language but I hope you understand me. I recently got a 580 that didn't turn on the typical short mosfet, as I didn't know exactly which one was short, I unsoldered them until I got the bad one out, I was able to remove the short and identify the bad mosfet, the gpu gives video again! but it has a problem that completely turns off vcore at random times or if I try to put a load on the gpu vcore drops to 0 I don't have much idea why because I don't know much about sapphire, any advice on where I could start looking or what problem it could...
      11-06-2023, 12:28 PM
    • jm942
      Hp Lh482p 5 short 3 long short after cpu vcore mosfet replacement
      by jm942
      Hi,
      My laptop went dead and after checking ,the main 19 volt power rail was shorted. After some checks i could identify that a high side vcore mosfet was shorted.
      I replaced the mosfet and now the white powerled is present , fans start spinning but capslock shows the famous 5 long and 3 short code.

      I checked the vcore voltages after replacement and i get for all 1.01 V so means for me that the driver is still working of the replaced shorted mosfet. On the Nvidia i measure around 0.8 V after the mosfets.
      I did voltage injection on the cpu with 0.7V and i have a current...
      07-11-2024, 05:11 AM
    • kotel studios
      Epox EP 85 MVP3C-M - 3.54v Vcore regardless of jumpers
      by kotel studios
      Hi,

      Recently I got an Epox EP-85 MVP3C-M board from scrap. After fixing the broken caps I powered it on without CPU and the jumpers set to 60Mhz FSB and 2x multiplier.
      Sadly, Vcc3 was stuck at 3.54v regardless of jumpers. Vcc2 (Vi/o I think) was also the same voltage.
      So, I've returned to the original configuration I got the board in - 100Mhz FSB and 4x multiplier. Voltages haven't changed at all.
      What I've tried so far:
      replace the original N-MOSFETs with beefier 60V ones for testing
      Resolder the resistors near the Vcore Jumper block
      Short Vcore...
      05-25-2025, 01:46 AM
    • Loading...
    • No more items.
    Working...