Originally posted by Diah
View Post
Announcement
Collapse
No announcement yet.
LG OLED55A1PUA
Collapse
X
-
Repair-it, can you tell me the marking of the emmc? My supposition is that oled screen stores a vcom value for each subpixel, that means for a supposing 12bit data needs at least 37mB, the most large spi i usually see is the 128mbit that holds only 25mb, and plus needs to store the complex fpga programming.. since the main chip is a SoC+fpga and not only fpga like lcd, i guess it stores also a dedicated linux operating system, in.fact there is also uart port for debugging.. the oled tcon are much different from lcd ones as it seems, every one can notice the presence also of huge ram, when in lcd is totally absent, ram means software presence...it maybe integrates also frc function.. the pixels voltages are similar, same vdd, hvdd, vgh, vglLast edited by Davi.p; 01-23-2024, 10:09 PM.
Comment
-
Originally posted by Diah View Post
i don't know from where you got this wrong INFO about OLED T-CON ? there are NO eMMC on T-CON at all...
Comment
-
with yours replacement Main boards... every things plugged in... only the 24V socket disconnect from T-con side.... plug it in wall... if it turn on and the optic lit red... send IN_STOP followed with 0413 with service RC. it will turn off to STBY state.. this will resetl rest this chip and the main one on MB
Comment
-
Originally posted by Diah View Postwith yours replacement Main boards... every things plugged in... only the 24V socket disconnect from T-con side.... plug it in wall... if it turn on and the optic lit red... send IN_STOP followed with 0413 with service RC. it will turn off to STBY state.. this will resetl rest this chip and the main one on MB
Comment
-
Originally posted by repair-it View Postok, Heard relay click when I pressed '0' and agin when I pressed '3'. LED remained on. What should I expect after hearing the relay click? Should I reconnect cable & try to power on?Last edited by Diah; 01-24-2024, 01:04 PM.
Comment
-
I guess it has the same LG brand Screen, and same problems.. my guess is the same as ever with LG displays.. bad solder.. needs solderings back to youth.. are you able? have you asked the spending threshold? Preparing for a repl. TCON.. and maybe pairing+recalibration costs / headhaches?? And if is main board? Sony famous for bad software, all withing EMMC..!! If i would be you i think better before handling a 77 monster..Last edited by Davi.p; 01-25-2024, 01:53 AM.
Comment
-
Originally posted by Davi.p View PostI guess it has the same LG brand Screen, and same problems.. my guess is the same as ever with LG displays.. bad solder.. needs solderings back to youth.. are you able? have you asked the spending threshold? Preparing for a repl. TCON.. and maybe pairing+recalibration costs / headhaches?? And if is main board? Sony famous for bad software, all withing EMMC..!! If i would be you i think better before handling a 77 monster..
Comment
-
I see you guys turning every discussion about OLED TVs in rocket science.
Here is ELI5 tutorial.
LG OLED
Unplug LVDS cables between main and Tcon, set turns on? Have a sound? If yes then Tcon/panel bad. Trash it.
You can play around by shortening Tcon sys_pow_off pin #40 on LVDS 51 pin connector on main board side.
That will force main to turn on and you would have all voltages present on Main board and Tcon as well. Your panel might lit up with lines or blotches.
You can also unplug 4 wide ribbons between Tcon and panel and check voltages or scope driver waveforms if you have high end oscilloscope and know what is to be seen on VBY1 lines.
Sony OLED
If you can't get set to turn on, in 90% of the time you would have bad Main board. Rest of 10% would be PS module.
If you unplug LVDS cables TV will go into shutdown with 4 or 5 red blinks, and UNLIKE LG, YOU WILL NOT HAVE ALL VOLTAGES PRESENT!
Also, bad panel would give you 4 or 5 red blinks.
No blinks, present 3.3V Stby and 12V run, 1.8V and 3.3V on EMMC, bad Main.
Comment
Comment