Announcement

Collapse
No announcement yet.

Quadro LED-40TN42S2T2HEVC

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Quadro LED-40TN42S2T2HEVC

    Hello.

    PS Vestel 17IPS62
    MB Vestel 17MB140

    TV died while in standby mode. Doesn't react to remote, or onboard on button in any way. No backlight. Standby light is off. Transformer buzzes silently.

    Quick visual inspection; no burn marks, caps look ok.

    Multimeter check unpowered; fuses are ok, electrolitic caps near or at rated capacitance, diodes ok.

    Multimeter cold side all boards disconnected from PS;
    mb connector 12v - 2.03v, stby - (-)2.96v, bkl and pwm 0v
    inverter connector 24v line is 6v

    all boards connected; 12v and 24v same as above, no easy access to other pins.

    Guessing the issue is the PS, but I have no idea what to look for next. Considering just buying a new board, but would like to confirm its the PS and find the exact problem if possible. Thanks.
    Tags: None
    #2
    Re: Quadro LED-40TN42S2T2HEVC

    What is voltage across main capacitor?
    I assume no responsibility for any stupid suggestions I might post.

    Comment

      #3
      Re: Quadro LED-40TN42S2T2HEVC

      I am assuming you mean the 2 400v capacitors, they are ~315v.

      Comment

        #4
        Re: Quadro LED-40TN42S2T2HEVC

        OK, on second measurement I'm getting 12.3v on 12v, and 35v for inverter now.

        Comment

          #5
          Re: Quadro LED-40TN42S2T2HEVC

          0v for stby, bkl and pwm

          Comment

            #6
            Re: Quadro LED-40TN42S2T2HEVC

            Now everything works. I'm guessing cold joints or something where the culprit, as I tested the voltages multiple times, with different board setups, and also I waited overnight to confirm the symptoms before opening it up. Now I will leave the tv disconnected overnight again, check if it works tomorrow and report back.

            Comment

              #7
              Re: Quadro LED-40TN42S2T2HEVC

              TV works well today. At least I can confirm the problem was the PS.
              For future reference the working voltages when only the PS was plugged in without any other boards were: 35v for the Vled pins, some volts for the CH_1,2,3,4, 12v on 12v pins, and 0v for stby, bkl and pwm.
              Thanks dskall for replying.
              Last edited by Guerilla3; 09-12-2022, 08:44 AM. Reason: Added additional info

              Comment

                #8
                Re: Quadro LED-40TN42S2T2HEVC

                If you have problems again you will need to resolder things like the transformer and connectors.
                I assume no responsibility for any stupid suggestions I might post.

                Comment

                  #9
                  Re: Quadro LED-40TN42S2T2HEVC

                  Will do, thanks again.

                  Comment

                    #10
                    Re: Quadro LED-40TN42S2T2HEVC

                    TV stopped working again. Tried reflowing most of the hot side, also transformers and electrolytic caps. DC voltages same as before for 12v and bkl. Main caps at 300+v.

                    Comment

                      #11
                      Re: Quadro LED-40TN42S2T2HEVC

                      Tried reflowing FETs, ICs and optocoupler.
                      Current situation is same as before; 12v line is 2v, and 35v line is 6v, both are lower by about 6x the needed voltage.
                      Main AC caps, and diodes before transformer are 300v+.

                      Comment

                      Previous template Next
                      Working...
                      X