The only problem I noticed is that the core heats up very quickly. When there is no heatsink, the voltages drop to 0V. But when the heatsink is installed, the voltages are constant.I measured the PCI lanes and there are no broken lines.I am open to all suggestions and recommendations.â€...
hallmark1730
Member
Last Activity: 03-02-2025, 04:58 PM
Joined: 04-05-2021
Location: Cologne
-
RTX 3090 all voltages normal but not post
Hello, Aorus 3090 xtreme model card does not post even though all voltages are correct.When I plug it in with another GPU, the motherboard stays on the GPU error light.That's why I can't test it from mats mods or check seems in windows.I checked the pex gate, there is 3.3 volt and 1.8 volt output.
The only problem I noticed is that the core heats up very quickly. When there is no heatsink, the voltages drop to 0V. But when the heatsink is installed, the voltages are constant.I measured the PCI lanes and there are no broken lines.I am open to all suggestions and recommendations.â€... -
Hello im from türkiye I am interested in video card repair -
Aorus rtx 3090 Xtrem Strange No post not detect But LCD on Fan spins
Hello, first of all, I do all my conversations with google translate. So if there is anything wrong with the meanings, please warn, I've been dealing with the this problem for about 5 days. I haven't found a solution yet. I will post videos and photos.The picture I drew is a bit ridiculous, but in short, (When I started it in this way, spark came out from the rx470. Because my cable replicator was from CPU to GPU, reverse voltage came.) this rx470 broke my other cards while trying, but except for the 2080s, I don't understand why the others are broken.all cards are connected via pci ex 1 risers.when... -
Re: RTX3070 not detected/ no display - has all voltages and pex reset question
Hello, I have a 3090 in a similar situation. The and logic gate with the code u811(74VHC1G08) is vin 1.8 v, but where is the problem with the 1st 2nd and 3rd legs grounding(multimeter is beeping all legs). 1st and 2nd legs 3.3 volts is required normally....Last edited by hallmark1730; 03-08-2023, 07:19 AM.Leave a comment:
-
Re: GTX 1070 Dual 8GB - Short Circuit on 3.3v Line
hello, is there an update. i have the same situation in 3090. u811 1,2 and 3 legs are short circuit (LOGIC 74LVC1G08GW)Leave a comment:
-
Re: XFX RX 5700XT No Display
is it work please updateLeave a comment:
-
Re: X555ld rev 3.3
ok i solved it clean a contack cleaner for motherboard and harddisk board connector its workLeave a comment:
-
Re: X555ld rev 3.3
I'm very sorry. The graphics card is working properly.I wanted to do a clean install because the pc is slowing down after bios reprogramed.but windows installation stuck at copying windows files 0%.try different usb-iso-diskpart-bios secure boot disabled but dont work.I can't clean installLeave a comment:
-
Re: X555ld rev 3.3
You are a best.Thank you very very much.you were very patient, kind and helpfulLeave a comment:
-
Re: X555ld rev 3.3
if plug the charger do not read or write add picture.
Even when I disconnect the usb, the light is on the programmer
NEW EDİT:I don't know why, but now he programed it. Windows is opening, I will check if my video card problem is fixed...Last edited by hallmark1730; 04-09-2021, 07:15 AM.Leave a comment:
-
Re: X555ld rev 3.3
I did the way you say. But I get the same error. please help me...Leave a comment:
-
Re: X555ld rev 3.3
i try programing but error this
Protection may be enabled. Press "Unprotect" and check datasheet
Current programmer: CH341
Old SREG: 01000000(0x40),
New SREG: 11111111(0xFF),
Programming memory(verifying)...
Verification error on address: 00000005
Execution time: 00:00:00.048
Current programmer: CH341
SPI ID: 2017C2
Current programmer: CH341
15:07:18
Protection may be enabled. Press "Unprotect" and check datasheet
Current programmer: CH341
Old SREG: 11110011(0xF3),...Leave a comment:
-
Re: X555ld rev 3.3
Thanks neoprogrammer is good list my chip mx25l6473e.Can I write the bios file directly? or do I need to find a dump file.i found a x555lb orijinal dump file Which one should I use
3.3 volt mode mandatory?...Last edited by hallmark1730; 04-09-2021, 06:06 AM.Leave a comment:
-
Re: X555ld rev 3.3
Hi again i received programmer(yes black pcb). created backup add here.I tried to write from ami before but bios did not accept it because it shows 306 ldb...Last edited by hallmark1730; 04-09-2021, 05:51 AM.Leave a comment:
-
Re: Asus main board : X555ld rev 2.0 & rev 3.3 & rev 3.6 bios
hello friends
asus x555LD rev.3.3(Case code:k555lb)but inside bios x555lbd.307(i think wrong bios)
n16s-gt-s-a2 nvidia chip inside.intel gpu work fine but gt940m is code 43 ?
please help me...Leave a comment:
-
Re: X555ld rev 3.3
can i use this. i will buy...Leave a comment:
-
Re: X555ld rev 3.3
i dont have a spi programmer please different way?
i crate backup for bios backup toolkit v2...Last edited by hallmark1730; 04-07-2021, 08:14 AM.Leave a comment:
-
Re: X555ld rev 3.3
Hello I added photos and bios.This is the bios file that asus accepts and installs with its own program.and i added the latest version 307...Leave a comment:
-
Re: X555ld rev 3.3
hi again i try before this bios but winflash message bios file is not valid.
this vram chip is n15 but i need n16s please help me...Leave a comment:
-
Re: X555ld rev 3.3
thank u i will try but not workink.my motherboard x555ld rev 3.3 n16s-gt-s-a2 nvidia cards not workingLeave a comment:
No activity results to display
Leave a comment: