Re: Samsung pn51d550c1f 5 blinks
VA is 58.2 VS is 210 second VS is also 210. All voltages from PS to main board are correct. I believe the "1" on my meter means overload.
landen_michael77
Senior Member
Last Activity: 09-10-2021, 10:00 AM
Joined: 05-25-2012
Location: streator, illinois
-
Last edited by landen_michael77; 10-09-2019, 08:13 AM. -
Samsung pn51d550c1f 5 blinks
Samsung pn51d550c1f 5 blinks. Screen flashes briefly when power button is hit. Getting ready to open it up today or tomorrow. Of coarse will test voltages. Any common issues with this model before I get started. Thanks in advance. Will report back on voltages.Last edited by landen_michael77; 10-08-2019, 01:39 PM. -
Re: LG 60pz550 sound but no picture
TV Timmy. Here are some pics. The red circles i get beeps with my multimeter in continuity mode. Pictures are of the top, and bottom area of board where i tested. They are out of order for some reason....Last edited by landen_michael77; 03-20-2019, 12:23 PM.Leave a comment:
-
Re: LG 60pz550 sound but no picture
Can i just put ground probe, on back of the panel, and just touch each pin with hot probe?Leave a comment:
-
Re: LG 60pz550 sound but no picture
I resoldered them on both z, and y before posting the question.Leave a comment:
-
Re: LG 60pz550 sound but no picture
Hi guys. I had one of these dropped off today. I think one of the copper coils is cracked on the zsus. Is there a way to test and be sure that is what is causing it to have no picture?Leave a comment:
-
Re: Sony Bravia KDL-55EX710
The only voltage i can check on the PS is the standby, because it will not turn on. I have 1.5 at the 3.3.Leave a comment:
-
Re: Sony Bravia KDL-55EX710
I freeze sprayed the main board, and it would turn on, but only for a couple secondsLeave a comment:
-
Re: Sony Bravia KDL-55EX710
Sorry guys. Thought I attached these to the original....Leave a comment:
-
Sony Bravia KDL-55EX710
Picked up a Sony Bravia KDL-55EX710. Has 7 blinks. Once in a great while will start. Normally it just clicks on the right back off. Has energy saving swith on the side instead of in the settings like normal. Standby is 1.5 instead of 3.3. Any sugestions? -
Re: Sharp Aquos LC-46D64U stand by with new boards!
I Will Be A S.O.B. !!!! Reflow worked on a LC-46D85UN
Leave a comment:
-
Re: Phillips 42pfl3603d/f7 CLicking
c104 is 4.7 changed it. Same thing. c102 is 47. changed it also. same thing. Im probably crazy but seems like the click is not as loud. Those were the only two I had on hand. I will have to order the others.Leave a comment:
-
Re: Phillips 42pfl3603d/f7 CLicking
looks like the cap reads 4.7 uf not 47. ????Leave a comment:
-
Re: Phillips 42pfl3603d/f7 CLicking
I dont know if it matters, but when I unplug the white, and black cable from the power supply(going to the main board) it does not make the click any longer. I am going to change these caps now if I have them. Thank youLeave a comment:
-
Re: Phillips 42pfl3603d/f7 CLicking
just uploaded pics. Internet is scketchy today.Leave a comment:
-
Re: Phillips 42pfl3603d/f7 CLicking
pictures...Leave a comment:
-
Phillips 42pfl3603d/f7 CLicking
Hello, I have a Phillips 42 inch Lcd tv. As soon as i plug it into an outlet it begins clicking. I assume it is trying to cycle on and off. All 12v pins seem to have the correct voltage. right about 12. The one that I did notice that was wrong is the 3v3 st. As the power supply clicks the voltage fluctuates between 0.90v up to 1.5v. It changes almost every time it cycles (clicks) On the (off) cycle it drops all the way to zero and when its cycles on it never goes above 1.5v. It continues doing this as long as I leave it plugged in. I see no visible bad caps. I believe I have isolated the click... -
Re: Phillips 42pfl3603d/f7 Constant Click
....Leave a comment:
-
Phillips 42pfl3603d/f7 Constant Clicking
Hello, I have a Phillips 42 inch Lcd tv. As soon as i plug it into an outlet it begins clicking. I assume it is trying to cycle on and off. All 12v pins seem to have the correct voltage. right about 12. The one that I did notice that was wrong is the 3v3 st. As the power supply clicks the voltage fluctuates between 0.90v up to 1.5v. It changes almost every time it cycles (clicks) On the (off) cycle it drops all the way to zero and when its cycles on it never goes above 1.5v. It continues doing this as long as I leave it plugged in. I see no visible bad caps. I believe I have isolated the click... -
Re: Philips 37PFL9604H T-Con issue?
Grab the top right corner, and bottom left corner of the tv and twist (lightly) and see if the picture clears up. If it does its a panel cable.Leave a comment:
No activity results to display
Leave a comment: