Re: Sega Dreamcast NTSC-U Revision 0 Launch Unit GD ROM PCB Board Short
Ok so I finally had some time to pull the chip and sure enough out of circuit the chips 12v pin is shorted to the chips ground pin so it's for sure the culprit. The cap pads no longer read as shorted with the chip out of circuit as well.
Now to find a replacement. Thanks for your help I appreciate it....
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
Re: Sega Dreamcast NTSC-U Revision 0 Launch Unit GD ROM PCB Board Short
c62, c63, c64 all check out ok.
U2 is a BA5986FM it very well could be the problem as it's on the same circuit the shorts are on. How would one test it with a DMM to find out if it's bad or not?
If I remove it from circuit and if the shorts on the cap pads appear normal would that tell me it's the fault? Or would that test not be accurate because it's missing from the circuit?
Where do you purchase your BA5986FM from when you fix PS2's? Where is the...
Leave a comment:
-
Sega Dreamcast NTSC-U Revision 0 Launch Unit GD ROM PCB Board Short
Hi everyone,
Symptom: When I press the power button the power LED lights up for a second and the fan etc spins for a second then the unit turns itself off and will not do the same thing again unless I unplug the power cable for a few minutes then plug it back in otherwise if I just turn the power switch off and back on right after it comes on for a second it will not come on again unless like I said unplug the power cord for a few minutes then plug it back in.
What I have done to try to isolate the issue so far:
The system powers on and stays on with...
-
Samsung Un60es6100 LED how to force power supply on?
Hey guys.
Here is a link to shopjimmy with the pictures of the power supply from this set [url]https://www.shopjimmy.com/samsung-bn44-00524a-pd60b1d_chs-power-supply-unit/[/url]
I would like to know which pins on the power supply I have to jump to force it on without the main board connected, so I could troubleshoot if I have a main board issue or a power supply issue?
I have read some things that I need a 1 ohm resistor to do it, but I don't think I have one on hand. I have done this on other sets before and never have used a resistor to do it. Please...
-
Sony XAV-68BT Car Touchscreen Stereo
Hi,
I need help identifying this blown part that's in the picture I included. It sits inside the unit right up against the back of the heatsink, I'm not sure if it's a power MOSFET or the amplifier, but it has two holes blown in it and the stereo will not power on just more smoke comes out of the part. I can't identify it because the burns removed some of the markings. Anyone have any ideas?...
-
Re: Samsung LED UN46H5203 No Backlights
This set belongs to a friend that says he doesn't want to spend money on it really and asked me if there is a way to jumper the LED to the next led, then turn down the backlight so he could get a bit more out of it. Is that possible?...
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
Great so I guess opening the panel it is sigh lol. I have many LEDs from tvs laying around could I not just replace the burnt out ones, if so are all LEDs the same?
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
Ok here are the correct pin readouts...
Pins 2 & 3 - 55.1v ( Panel lights up)
Pins 4 & 6 - 29.9v (Panel lights up)
Pins 7 & 8 - 313v (panel doesn't light up)
What does this mean?...
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
I'm getting mixed opinions, I would prefer not to have to risk taking out the panel if I don't have to.
Could anyone be more sure what's happening?
budm any ideas I haven't heard your opinion yet?...
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
The voltages on the LED tester say...
Pin 1 & 2 - 55.1v
Pin 4 - 29.9v
Pin 7 - 0v
Pin 8 & 9 - 85.8v
What do you figure from those numbers?...
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
Tried that and same thing....
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
CNL802 CONNECTOR ON PSU TO LED's TESTED WITH CABLE DISCONNECTED WITH POWER ON
Pin 1 D1+ - 305.2v
Pin 2 D1+ - 305.0v
Pin 3 S1- - 0v
Pin 4 S2+ - 0v
Pin 5 NC - 0v
Pin 6 S2- - 0v
Pin 7 S3+ - 0v
Pin 8 D1- - 0v
Pin 9 D1- - 0v
CNL802 CONNECTOR ON PSU TO LED's TESTED WITH CABLE DISCONNECTED WITH TV ON STANDBY
Pin 1 D1+ - 207.5v
Pin 2 D1+ - 207.7
Pin 3 S1- - 0v
Pin...Last edited by sfernandes; 02-11-2020, 11:19 PM.
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
CNL802 CONNECTOR ON PSU TO LED's
ON STATE
Pin 1 D1+ - 310v
Pin 2 D1+ - 308v
Pin 3 S1- - 260v
Pin 4 S2+ - 262v
Pin 5 NC - 0v
Pin 6 S2- - 235v
Pin 7 S3+ - 233v
Pin 8 D1- - 0v
Pin 9 D1- - 0v
STANDBY STATE
Pin 1 D1+ - 208v
Pin 2 D1+ - 208v
Pin 3 S1- - 159v
Pin 4 S2+ - 159v
Pin 5 NC - 0v
...
Leave a comment:
-
Re: Samsung LED UN46H5203 No Backlights
My bad, I'm sorry for my mistake here are new measurements.
ON STATE
CNM803 on PSU from Main
Pin 1 A13v - 12.94v
Pin 2 OD_UD - 3.297v
Pin 3 A13v - 12.94v
Pin 4 BLU_PWM - 1.574v
Pin 5 A13v - 12.94v
Pin 6 PWR_On/Off - 3.328v
Pin 7 A13v - 12.94v
Pin 8 GND - 0v
Pin 9 GND - 0v
Pin 10 GND - 0v
STANDBY STATE
CNM803 on...
Leave a comment:
-
Samsung LED UN46H5203 No Backlights
Hey guys,
I need some help trying to troubleshoot this set.
I have tested the LED Backlights with the Shopjimmy LED backlight tester and I could see through the back of the panel the LEDs lighting up.
Flashing a flashlight into the panel I could see the image.
I have taken voltage measurements here they are...
TV in running mode
CNM803 CONNECTOR ON PSU
Pin 1 - 13v
Pin 2 - 13v
Pin 3 - 13v
Pin 4 - 13v
Pin 5 - 0v
Pin 6 - 3.297v
Pin...Last edited by sfernandes; 02-11-2020, 03:23 PM.
-
Re: Samsung Plasma PN43F4500BF will not turn on please help
Ok thank you Tom66 I will replace the main. Also thank you to everyone else for helping me with this I greatly appreciate it. I'll report back once I get the main after Christmas because the post office is crazy busy now I don't want my package in limbo. Cheers....
Leave a comment:
-
Re: Samsung Plasma PN43F4500BF will not turn on please help
Ok I did this and got the test patterns to come up, but it does the same thing shows only a few patterns then screen goes dark then shows the patterns from the beginning and again goes black does this over and over. I measured the voltages during the test patterns and same thing voltages correct then drop then correct then drop over and over.
I then decide to run the test patterns forcing the PSU on by jumping the pins and disconnecting the power from the power supply to the main and doing...
Leave a comment:
No activity results to display
Show More
Leave a comment: